- 您现在的位置：买卖IC网 > PDF目录1915 > DS3141+ (Maxim Integrated Products)IC FRAMER DS3/E3 SNGL 144CSBGA PDF资料下载
参数资料
| 型号： | DS3141+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/88页 |
| 文件大小： | 0K |
| 描述： | IC FRAMER DS3/E3 SNGL 144CSBGA |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 160 |
| 控制器类型： | DS3/E3 调帧器 |
| 接口： | LIU |
| 电源电压： | 3.135 V ~ 3.465 V |
| 电流 - 电源： | 80mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 144-BGA，CSPBGA |
| 供应商设备封装： | 144-TECSBGA（13x13） |
| 包装： | 托盘 |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页
DS3141/DS3142/DS3143/DS3144 Single/Dual/Triple/Quad DS3/E3 Framers
10 of 88
5.3 Transmit Formatter System Interface Pins
NAME
TYPE
FUNCTION
TICLK
I
Transmit Input Clock. TICLK samples the TDAT, TDEN/TGCLK, TSOF, TOH, and TOHEN input pins.
TICLK accepts a smooth clock or a gapped clock up to 52MHz. When the framer is connected to an LIU
without a jitter attenuator, TICLK should be an ungapped, transmission-quality DS3 or E3 clock (
±20ppm,
low jitter) to meet the frequency accuracy and jitter requirements for transmission. The default active
sampling edge of TICLK is the rising edge. To make the negative edge the active sampling edge, set
MC3:TICLKI = 1.
TDAT
I
Transmit Data Input. In C-Bit Parity DS3 mode, payload bits are clocked into the transmit formatter on
TDAT. In M23 DS3 mode and E3 mode, payload bits, stuff opportunity bits and C bits are clocked in on
TDAT. TDAT is sampled on the active sampling edge of TICLK. The default active sampling edge of
TICLK is the rising edge. To make the negative edge the active sampling edge, set MC3:TICLKI = 1.
TDAT can be internally inverted by setting MC3:TDATI = 1.
TDEN/
TGCLK
O
Transmit Data Enable/Transmit Gapped Clock. The transmit formatter can be configured to either output a
data enable (TDEN) or a gapped clock (TGCLK). In data enable mode, TDEN goes active when payload
data should be made available on the TDAT input pin and inactive when the formatter is inserting framing
overhead. In gapped clock mode, TGCLK acts as a demand clock for the TDAT input, toggling for each
payload bit position and not toggling when the formatter is inserting framing overhead. In DS3 mode,
overhead data is defined as the M bits, F bits, C bits, X bits, and P bits. In E3 mode, overhead data is
defined as the FAS word, RAI bit, and Sn bit (bits 1 to 12). To configure the transmit formatter for data
TDEN is normally active high; to make TDEN active low, set MC3:TDENI = 1. TGCLK normally is the
same polarity as TICLK; to invert TGCLK, set MC3:TDENI = 1. In the transmit pass-through mode
(T3E3CR1:TPT = 1), TDEN/TGCLK continues to mark the payload positions in the original frame
established before TPT was activated. This pin can also be made to output a constant transmit clock by
setting MC2:TCCLK = 1. This constant clock is useful for certain applications that need to use the TOH
and TOHEN pins during payload loopback.
TSOF
O/I
Transmit Start-of-Frame. TSOF indicates the DS3 or E3 frame boundary on the outgoing transmit data
stream. When TSOFC = 1 in the MC3 register, TSOF is an output and pulses high for one TICLK cycle
during the last bit of each DS3 or E3 frame. When TSOFC = 0, TSOF is an input and is sampled to set the
transmit DS3 or E3 frame boundary. See Figure 5-1 for functional timing. Note that the reset default is for
TSOF to be an input. Some applications require an external pullup or pulldown resistor on TSOF to keep it
from floating during power-up and reset. TSOF is normally active high. Set MC3:TSOFI = 1 to make TSOF
active low. If transmit pass-through (TPT) mode is enabled (T3E3CR1:TPT = 1) and TSOF is an output,
TSOF continues to mark the original frame position that was established before TPT activation.
TOHEN
I
Transmit Overhead Enable. Together the TOHEN and TOH pins make a simple, general-purpose
transmit-overwrite port. This port is usually used to overwrite overhead bit positions (such as unused C
bits in C-Bit Parity mode), but payload bits can be overwritten as well. During any clock cycle in which
TOHEN is active, the formatter sources the TOH pin rather than the TDAT pin or the internal overhead
generation logic. In DS3 mode, parity is not recalculated if any payload bits are overwritten. TOHEN can
be internally inverted by setting MC3:TOHENI = 1.
TOH
I
Transmit Overhead Data. Together the TOHEN and TOH pins make a simple, general-purpose transmit-
overwrite port. This port is usually used to overwrite overhead bit positions (such as unused C bits in C-Bit
Parity mode), but payload bits can be overwritten as well. During any clock cycle in which TOHEN is
active, the formatter sources the TOH pin rather than the TDAT pin or the internal overhead generation
logic. TOH can be inverted by setting MC3:TOHI = 1.
TMEI
I
Transmit Manual-Error Insert. This pin is used to manually control the insertion of errors in the DS3 or E3
frame structure or the line coding. This pin is enabled when MEIMS = 1 in the T3E3EIC register. A single
error is normally inserted on the rising edge of TMEI. The other bits in the T3E3EIC register control which
types of errors are inserted. All framers on the device share this pin.
相关PDF资料 |
PDF描述 |
|---|---|
| DS31412N | IC 12CH DS3/3 FRAMER 349-BGA |
| DS3150TN | IC LIU T3/E3/STS-1 IND 48-TQFP |
| DS3154N+ | IC LIU DS3/E3/STS-1 QD 144CSBGA |
| DS3164+ | IC ATM/PACKET PHY QUAD 400-BGA |
| DS3170+ | IC TXRX DS3/E3 100-CSBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3141+ | 功能描述:网络控制器与处理器 IC Single DS3/E3 Framer RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS314-1010NR WAF | 制造商:ON Semiconductor 功能描述: |
| DS31412 | 功能描述:网络控制器与处理器 IC 12 Port DS3/E3 Framer RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS31412N | 功能描述:网络控制器与处理器 IC 12 Port DS3/E3 Framer RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS31415 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:3-Input, 4-Output, Single DPLL Timing IC with Sub-ps Output Jitter and 1588 Clock |
发布紧急采购，3分钟左右您将得到回复。