- 您现在的位置：买卖IC网 > PDF目录16258 > DS3254DK (Maxim Integrated Products)KIT DEMO FOR DS3254 PDF资料下载
参数资料
| 型号： | DS3254DK |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 31/71页 |
| 文件大小： | 0K |
| 描述： | KIT DEMO FOR DS3254 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 设计资源： | DS3254DK Gerber Files |
| 标准包装： | 1 |
| 主要目的： | 电信，线路接口单元（LIU） |
| 已用 IC / 零件： | DS3254 |
| 已供物品： | 板，CD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页
DS3251/DS3252/DS3253/DS3254
37 of 71
15. CPU INTERFACES
When the HW pin is logic 0 the device is in CPU bus mode. The default CPU interface is 8-bit parallel.
15.1 Parallel Interface
When the device is in CPU bus mode, by default it presents a generic 8-bit parallel microprocessor interface. When
the MOT pin is logic 1, the interface is Motorola-style with
CS, R/W, and DS control lines. When MOT = 0, the
interface is Intel-style with
CS, RD, and WR control lines. In both styles, the interface supports both multiplexed and
nonmultiplexed operation. For multiplexed operation, wire A[5:0] to D[5:0], wire D[7:0] to the CPU’s multiplexed
address/data bus, and connect the ALE pin to the appropriate pin on the micro. For nonmultiplexed operation, wire
ALE high and wire A[5:0] and D[7:0] to the appropriate pins on the micro. See Table 17-H, Figure 17-3 and Figure
17-4 for parallel interface timing diagrams and parameters.
15.2 SPI Interface
When the MOT,
RD, and WR pins are all low and the ALE pin is high, the device presents an SPI interface on the
CS, SCLK, SDI, and SDO pins. SPI is a widely-used master/slave bus protocol that allows a master device and one
or more slave devices to communicate over a serial bus. The DS325x is always a slave device. Masters are
typically microprocessors, ASICs or FPGAs. Data transfers are always initiated by the master device, which also
generates the SCLK signal. The DS325x receives serial data on the SDI pin and transmits serial data on the SDO
pin. SDO is high-impedance except when the DS325x is transmitting data to the bus master.
Clock Polarity and Phase. The CPOL pin defines the polarity of SCLK. When CPOL = 0, SCLK is normally low
and pulses high during bus transactions. When CPOL = 1, SCLK is normally high and pulses low during bus
transactions. the CPHA pin sets the phase (active edge) of SCLK. When CPHA = 0, data is latched in on SDI on
the leading edge of the SCLK pulse and updated on SDO on the trailing edge. When CPHA = 1, data is latched in
on SDI on the trailing edge of the SCLK pulse and updated on SDO on the following leading edge.
See Figure 15-1.
Bit Order. The control byte and all data bytes are transmitted MSB first on both SDI and SDO.
Device Selection. Each SPI device has its own chip-select line. To select the DS325x, pull its
CS pin low.
Control Byte. After
CS is pulled low, the bus master transmits the control byte during the first eight SCLK cycles.
The control byte has the form R/
W A5 A4 A3 A2 A1 A0 BURST, where A[5:0] is the register address, R/W is the
data direction bit (1 = read, 0 = write), and BURST is the burst bit (1 = burst access, 0 = single-byte access). In the
discussion that follows, a control byte with R/
W = 1 is a read control byte, while a control byte with R/W = 0 is a
write control byte.
Single-Byte Writes. See Figure 15-2. After
CS goes low, the bus master transmits a write control byte with
BURST = 0 followed by the data byte to be written. The bus master then terminates the transaction by pulling
CS
high.
Single-Byte Reads. See Figure 15-2. After
CS goes low, the bus master transmits a read control byte with
BURST = 0. The DS325x then responds with the requested data byte. The bus master then terminates the
transaction by pulling
CS high.
Burst Writes. See Figure 15-2. After
CS goes low, the bus master transmits a write control byte with BURST = 1
followed by the first data byte to be written. The DS325x receives the first data byte on SDI, writes it to the
specified register, increments its internal address register, and prepares to receive the next data byte. If the master
continues to transmit, the DS325x continues to write the data received and increment its address counter. After the
address counter reaches FFh it rolls over to address 00h and continues to increment.
Burst Reads. See Figure 15-2. After
CS goes low, the bus master transmits a read control byte with BURST = 1.
The DS325x then responds with the requested data byte on SDO, increments its address counter, and pre-fetches
the next data byte. If the bus master continues to demand data, the DS325x continues to provide the data on SDO,
increment its address counter, and pre-fetch the following byte. After the address counter reaches FFh it rolls over
to address 00h and continues to increment.
相关PDF资料 |
PDF描述 |
|---|---|
| GCA32DRMH-S288 | CONN EDGECARD 64POS .125 EXTEND |
| EET-UQ2G471CA | CAP ALUM 470UF 400V 20% SNAP |
| UCY2G680MHD | CAP ALUM 68UF 400V 20% RADIAL |
| RCC22DCMS | CONN EDGECARD 44POS .100 WW |
| VE-JWK-EY-S | CONVERTER MOD DC/DC 40V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3254N | 功能描述:网络控制器与处理器 IC Quad DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS3254N# | 功能描述:网络控制器与处理器 IC Quad DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS3254N+ | 功能描述:网络控制器与处理器 IC Quad DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS3254NA3 | 制造商:Maxim Integrated Products 功能描述:QUAD ENH DS3/E3 LIU REV A3 IND - Rail/Tube |
| DS3256 | 功能描述:网络控制器与处理器 IC X6 T3/E3 Line Interface Unit RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。