- 您现在的位置：买卖IC网 > PDF目录16871 > EVAL-AD5560EBUZ (Analog Devices Inc)BOARD EVALUATION FOR AD5560 PDF资料下载
参数资料
| 型号： | EVAL-AD5560EBUZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 27/68页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD5560 |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电源监控器/跟踪器/序列发生器 |
| 已用 IC / 零件： | AD5560 |
| 次要属性： | 串行接口 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页
Data Sheet
AD5560
Rev. D | Page 33 of 68
DIE TEMPERATURE SENSOR AND THERMAL
SHUTDOWN
There are three types of temperature sensors in the AD5560.
The first is a temperature sensor available on the MEASOUT
pin and expressed in voltage terms. Nominally at 25°C, this
sensor reads 1.54 V. It has a temperature coefficient of
4.7 mV/°C. This sensor is active during power-down mode.
Die Temp = (VMEASOUT(TSENSE) 1.54)/0.0047 + 25°C
Based on typical temperature sensor output voltage at
25°C and output scaling factor.
The second type of temperature sensor is related to the
thermal shutdown feature in the device. Here, there are
sensors located in the middle of the enabled power stage,
which are used to trip the thermal shutdown. The thermal
shutdown feature senses only the power stages, and the power
stage that it senses is determined by the active stage.
If ranges of <25 mA are selected, the EXTFORCE1 sensor is
monitored. The EXTFORCE1 power stage itself is made
up of three identical stages, but the thermal shutdown is
activated by only one stage (EXTFORCE1B). Similarly, the
EXTFORCE2 stage is made up of two identical output
stages, but the thermal shutdown can be activated by only
one stage (EXTFORCE2A).
The thermal shutdown circuit monitors these sensors and,
in the event of the die temperature exceeding the program-
mable threshold temperature (100°C, 110°C, 120°C, 130°C
(default)), the device protects itself by inhibiting the force
amplifier stage, clearing SW-INH in DPS Register 1 and
flagging the overtemperature event via the open-drain
TMPALM pin, which can be programmed to be either
latched or unlatched. These temperature sensors can be
read via the MEASOUT pin by selecting them in the
diagnostic register (Table 23, VPTAT low and VPTAT
high). They are expressed in voltage and to scale to
temperature. They must be referred to the VTSD reference
voltage levels (see Table 23) also available on MEASOUT.
This set of sensors is not active in power-down mode.
Die Temp_y = {(VPTAT_x VTSD_low)/[(VTSD_high
VTSD_low)/(Temp_high – Temp_low)]} + Temp_low
where:
x, y are (high, NPN) and (low, PNP).
Temp_low = 273°C.
Temp_high = +130°C.
The third set of temperature sensors is an array of thermal
diodes scattered across the die. These diodes allow the user
to evaluate the temperature of different parts of the die and
are of great use to determine the temperature gradients
across the die and the temperature of the accurate portions
of the die when the device is dissipating high power. For
further details on the thermal array and locations, see the
diagnostic register section in Table 23.
These diodes can be muxed out onto the GPO pin. The
diagnostic register (Address 0x7) details the addressing and
location of the diodes. These can be used for diagnostic
purposes to determine the thermal gradients across the die
and across a board containing many AD5560 devices. When
selected, the anode of each diode is connected to GPO and
the cathode to AGND. The AD5560 evaluation board uses
the ON Semiconductor ADT7461 temperature sensor for
the purpose of analyzing the temperature at different
points across the die.
Note that, when a thermal shutdown occurs, as the force
amplifier is inhibited or tristated, user intervention is required
to reactivate the device. It is necessary to clear the temperature
alarm flag by issuing a read command of Register Address 0x44
(alarm status and clear alarm status register, Table 25), and
then issuing a new write to the DPS Register 1 (SW-INH = 1)
to reenable the force amplifier.
See also the Thermal Considerations section.
MEASURE OUTPUT (MEASOUT)
The measured DUT voltage, current (voltage representation
of DUT current), KSENSE, or die temperature is available on
MEASOUT with respect to AGND. The default MEASOUT
range is the forced voltage range for voltage measure and
current measure (nominally ±12.81 V, depending on reference
voltage and offset DAC) and includes overrange to allow for
system error correction.
The serial interface allows the user to select another MEASOUT
range of (1.025 × VREF) to AGND; this range is suitable for use
with an ADC with a smaller input range.
To allow for system error correction, there is additional gain
for the force function. If this overrange is used as intended,
the output range on MEASOUT scales accordingly.
The MEASOUT line can be tristated via the serial interface.
When using low supply voltages, ensure that there is sufficient
headroom and footroom for the required force voltage range.
VMID VOLTAGE
The midcode voltage (VMID) is used in the measure current
amplifier block to center the current ranges at about 0 A.
This is required to ensure that the quoted current ranges can
be achieved when using offset DAC settings other than the
default. VMID corresponds to 0x8000 or the DAC midcode
value, that is, the middle of the voltage range set by the offset
DAC setting (see Table 15 and Figure 56).
VMID = 5.125 × VREF × (32,768/216) (5.125 × VREF ×
(OFFSET_DAC_CODE/216))
or
VMID = 5.125 × VREF × ((32,768 Offset DAC)/216)
相关PDF资料 |
PDF描述 |
|---|---|
| EVAL-AD5522EBDZ | BOARD EVAL FOR 14X14MM AD5522 |
| EVAL-AD5520EBZ | BOARD EVAL FOR AD5520 |
| MAX6198AESA+T | IC VREF SERIES PREC 4.096V 8SOIC |
| QPI-5-EVAL1 | EVALUATION BOARD FOR QPI-5 |
| H6MMH-4006M | DIP CABLE - HDM40H/AE40M/HDM40H |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD5570EB | 制造商:Analog Devices 功能描述:DEV TOOLS, TRUE ACCURACY, 16BIT 12V/ 15V, SERL INPUT VOLT O - Bulk |
| EVAL-AD5570EBZ | 功能描述:BOARD EVALUATION FOR AD5570 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5570SDZ | 功能描述:BOARD EVAL FOR AD5570 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5590EBZ | 功能描述:BOARD EVAL FOR AD5590 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD5620EB | 制造商:AD 制造商全称:Analog Devices 功能描述:Single, 12-/14-/16-Bit nanoDAC with 5 ppm/C On-Chip Reference in SOT-23 |
发布紧急采购，3分钟左右您将得到回复。