- 您现在的位置：买卖IC网 > PDF目录4588 > IDT72V51246L6BB8 (IDT, Integrated Device Technology Inc)IC FLOW CTRL MULTI QUEUE 256-BGA PDF资料下载
参数资料
| 型号： | IDT72V51246L6BB8 |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 10/56页 |
| 文件大小： | 0K |
| 描述： | IC FLOW CTRL MULTI QUEUE 256-BGA |
| 标准包装： | 1,000 |
| 类型： | 多队列流量控制 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 256-BBGA |
| 供应商设备封装： | 256-BGA（17x17） |
| 包装： | 带卷 (TR) |
| 其它名称： | 72V51246L6BB8 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
18
IDT72V51236/72V51246/72V51256 3.3V, MULTI-QUEUE FLOW-CONTROL DEVICES
(4 QUEUES) 36 BIT WIDE CONFIGURATION 589,824, 1,179,648 and 2,359,296 bits
COMMERCIALANDINDUSTRIAL
TEMPERATURERANGES
cycles are required for the device to load its internal setup registers. When a
single multi-queue is used, the completion of device programming is signaled
bythe
SENOoutputofadevicegoingfromHIGHtoLOW.Note,thatSENImust
be held LOW when a device is setup for default programming mode.
When multi-queue devices are connected in expansion mode, the
SENI of
thefirstdeviceinachaincanbeheldLOW.The
SENOofadeviceshouldconnect
to the
SENIofthenextdeviceinthechain.TheSENOofthefinaldeviceisused
to indicate that default programming of all devices is complete. When the final
SENO goes LOW normal operations may begin. Again, all devices will be
programmed with their maximum number of queues and the memory divided
equally between them. Please refer to Figure 8, Default Programming.
READING AND WRITING TO THE IDT MULTI-QUEUE
FLOW-CONTROL DEVICE
The IDT72V51236/72V51346/72V51256 multi-queue flow-control de-
vices can be configured in two distinct modes, namely Standard Mode and
Packet Mode.
STANDARD MODE OPERATION (PKT = LOW on Master Reset)
WRITE QUEUE SELECTION AND WRITE OPERATION
(STANDARD MODE)
The IDT72V51236/72V51346/72V51256 multi-queue flow-control de-
vices can be configured up to a maximum of 4 queues into which data can be
written via a common write port using the data inputs (Din), write clock (WCLK)
and write enable (
WEN). The queue to be written is selected by the address
present on the write address bus (WRADD) during a rising edge on WCLK
while write address enable (WADEN) is HIGH. The state of
WEN does not
impact the queue selection. The queue selection is requires 2 WCLK cycles.
All subsequent data writes will be to this queue until another queue is selected.
Standard mode operation is defined as individual words will be written to the
device as opposed to Packet Mode where complete packets may be written.
The write port is designed such that 100% bus utilization can be obtained. This
means that data can be written into the device on every WCLK rising edge
including the cycle that a new queue is being addressed.
Changing queues requires a minimum of 2 WCLK cycles on the write port
(see Figure 9, Write Queue Select, Write Operation and Full flag Operation).
WADEN goes high signaling a change of queue (clock cycle “A”). The address
onWRADDatthattimedeterminesthenextqueue.Datapresentedduringthat
cycle (“A”) and the next cycle (“B”), will be written to the active (old) queue,
provided
WEN is active LOW. If WEN is HIGH (inactive) for these two clock
cycles, data will not be written in to the previous queue. The write port discrete
full flag will update to show the full status of the newly selected queue (Q
X) at
this last cycle’s rising edge (“B”). Data present on the data input bus (Din), can
be written into the newly selected queue (Q
X) on the rising edge of WCLK on
the second cycle (“C”) following a change of queue, provided
WEN is LOW
and the new queue is not full. If the newly selected queue is full at the point of
its selection, any writes to that queue will be prevented. Data cannot be written
into a full queue.
Refer to Figure 9, Write Queue Select, Write Operation and Full flag
Operation, Figure 10, Write Operations & First Word Fall Through for timing
diagrams and Figure 11, Full Flag Timing in Expansion Mode for timing
diagrams.
TABLE 1 — WRITE ADDRESS BUS, WRADD[4:0]
Operation WCLK WADEN
FSTR
WRADD[4:0]
Write Queue
Select
10
01
Device Select
(Compared to
ID0,1,2)
Write Queue Address
(2 bits = 4 Queues)
432
1 0
432
1 0
Device Select
(Compared to
ID0,1,2)
XX
PAFn Flag Bus
Device Select
5937 drw05
相关PDF资料 |
PDF描述 |
|---|---|
| LFXP6E-4Q208I | IC FPGA 5.8KLUTS 142I/O 208-PQFP |
| LFXP6C-5Q208C | IC FPGA 5.8KLUTS 142I/O 208-PQFP |
| LFXP6C-4Q208I | IC FPGA 5.8KLUTS 142I/O 208-PQFP |
| LFXP6E-4QN208I | IC FPGA 5.8KLUTS 208PQFP |
| LFXP6E-5QN208C | IC FPGA 5.8KLUTS 208PQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IDT72V51246L7-5BB | 功能描述:IC FLOW CTRL MULTI QUEUE 256-BGA RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
| IDT72V51246L7-5BB8 | 功能描述:IC FLOW CTRL MULTI QUEUE 256-BGA RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
| IDT72V51246L7-5BBI | 功能描述:IC FLOW CTRL MULTI QUEUE 256-BGA RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
| IDT72V51253L6BB | 功能描述:IC FLOW CTRL MULTI QUEUE 256-BGA RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
| IDT72V51253L6BB8 | 功能描述:IC FLOW CTRL MULTI QUEUE 256-BGA RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
发布紧急采购，3分钟左右您将得到回复。