参数资料
| 型号： | ISL6308CRZ |
| 厂商： | Intersil |
| 文件页数： | 10/28页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM 3PHASE BUCK 40-QFN |
| 标准包装： | 500 |
| 应用： | 控制器，DDR |
| 输入电压： | 5 V ~ 12 V |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 2.3 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 供应商设备封装： | 40-QFN（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
ISL6308
Another benefit of interleaving is to reduce input ripple
current. Input capacitance is determined in part by the
maximum input ripple current. Multiphase topologies can
improve overall system cost and size by lowering input ripple
current and allowing the designer to reduce the cost of input
capacitance. The example in Figure 2 illustrates input
currents from a three-phase converter combining to reduce
the total input ripple current.
The converter depicted in Figure 2 delivers 1.5V to a 36A load
from a 12V input. The RMS input capacitor current is 6.1A.
Compare this to a single-phase converter also stepping down
12V to 1.5V at 36A. The single-phase converter has a 13.3A
RMS input capacitor current. The single-phase converter
must use an input capacitor bank with twice the RMS current
capacity as the equivalent three-phase converter.
INPUT-CAPACITOR CURRENT
CHANNEL 3
INPUT CURRENT
CHANNEL 2
INPUT CURRENT
CHANNEL 1
INPUT CURRENT
FIGURE 2. CHANNEL INPUT CURRENTS AND INPUT-
CAPACITOR RMS CURRENT FOR 3-PHASE
CONVERTER
capacitor RMS current based on load current, duty cycle,
and the number of channels. They are provided as aids in
determining the optimal input capacitor solution.
PWM Operation
The timing of each converter leg is set by the number of
active channels. The default channel setting for the ISL6308
is three. One switching cycle is defined as the time between
the internal PWM1 pulse termination signals. The pulse
termination signal is the internally generated clock signal
that triggers the falling edge of PWM1. The cycle time of the
pulse termination signal is the inverse of the switching
frequency set by the resistor between the FS pin and
ground. Each cycle begins when the clock signal commands
PWM1 to go low. The PWM1 transition signals the internal
channel 1 MOSFET driver to turn off the Channel 1 upper
MOSFET and turn on the Channel 1 synchronous MOSFET.
In the default channel configuration, the PWM2 pulse
10
terminates one third of a cycle after the PWM1 pulse. The
PWM3 pulse terminates one third of a cycle after PWM2.
If PVCC3 is left open or connected to ground, two channel
operation is selected and the PWM2 pulse terminates one
half of a cycle after the PWM1 pulse terminates. If both
PVCC3 and PVCC2 are left open or connected to ground,
single channel operation is selected. The 2PH and 3PH
inputs can also be used to accomplish this function. Once a
PWM pulse transitions low, it is held low for a minimum of
one third cycle. This forced off time is required to ensure an
accurate current sample. Current sensing is described in the
next section. After the forced off time expires, the PWM
output is enabled. The PWM output state is driven by the
position of the error amplifier output signal, VCOMP, minus
the current correction signal relative to the sawtooth ramp as
illustrated in Figure 3. When the modified VCOMP voltage
crosses the sawtooth ramp, the PWM output transitions
high. The internal MOSFET driver detects the change in
state of the PWM signal and turns off the synchronous
MOSFET and turns on the upper MOSFET. The PWM signal
will remain high until the pulse termination signal marks the
beginning of the next cycle by triggering the PWM signal low.
Channel Current Balance
One important benefit of multi-phase operation is the thermal
advantage gained by distributing the dissipated heat over
multiple devices and greater area. By doing this the designer
avoids the complexity of driving parallel MOSFETs and the
expense of using expensive heat sinks and exotic magnetic
materials.
In order to realize the thermal advantage, it is important that
each channel in a multi-phase converter be controlled to carry
about the same amount of current at any load level. To
achieve this, the currents through each channel must be
sampled every switching cycle. The sampled currents, I n ,
from each active channel are summed together and divided
by the number of active channels. The resulting cycle average
current, I AVG , provides a measure of the total load current
demand on the converter during each switching cycle.
Channel current balance is achieved by comparing the
sampled current of each channel to the cycle average current,
and making the proper adjustment to each channel pulse
width based on the error. Intersil’s patented current-balance
method is illustrated in Figure 3, with error correction for
Channel 1 represented. In Figure 3, the cycle average
current, I AVG , is compared with the Channel 1 sample, I 1 , to
create an error signal I ER .
The filtered error signal modifies the pulse width
commanded by V COMP to correct any unbalance and force
I ER toward zero. The same method for error signal
correction is applied to each active channel.
FN9208.4
September 30, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| ACM18DRSN-S288 | CONN EDGECARD EXTEND 36POS 0.156 |
| RCM22DTAD-S189 | CONN EDGECARD 44POS R/A .156 SLD |
| MAX8860EUA28+ | IC REG LDO 2.82V/ADJ .3A 8-UMAX |
| 2512-562K | INDUCTOR POWER 5.6UH MOLDED SMD |
| ACM18DRSH-S288 | CONN EDGECARD EXTEND 36POS 0.156 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6308CRZR5374 | 制造商:Intersil Corporation 功能描述:ISL6308CRZ W/ 24HR BURN-IN - Rail/Tube 制造商:Intersil Corporation 功能描述:IC CTRLR PWM 3PHASE BUCK 40-QFN 制造商:Intersil 功能描述:ISL6308CRZ W/24HRU RN-IN |
| ISL6308CRZ-T | 功能描述:电压模式 PWM 控制器 DAC-LESS MULTI-PHS PWM CNTRLR W/3-DRVRS RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL6308CRZ-TR5374 | 制造商:Intersil Corporation 功能描述:ISL6308CRZ W/ 24HR BURN-IN - Tape and Reel 制造商:Intersil Corporation 功能描述:IC CTRLR PWM 3PHASE BUCK 40-QFN 制造商:Intersil 功能描述:ISL6308CRZ W/24HRU RN-IN |
| ISL6308CRZ-TR5453 | 制造商:Intersil Corporation 功能描述:STD. ISL6308CRZ-T W/GOLD BOND WIRE ONLY - Tape and Reel |
| ISL6308EVAL1Z | 制造商:Intersil Corporation 功能描述:ISL6308 EVALUATION BOARD 1 - ROHS COMPLIANT - QFN - Bulk |
发布紧急采购，3分钟左右您将得到回复。