- 您现在的位置：买卖IC网 > PDF目录16826 > KSZ8864RMN-EVAL (Micrel Inc)BOARD EVALUATION FOR KSZ8864RMN PDF资料下载
参数资料
| 型号： | KSZ8864RMN-EVAL |
| 厂商： | Micrel Inc |
| 文件页数： | 50/111页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR KSZ8864RMN |
| 标准包装： | 1 |
| 主要目的： | 接口，以太网控制器（PHY 和 MAC） |
| 嵌入式： | 否 |
| 已用 IC / 零件： | KSZ8864RMN |
| 已供物品： | 板 |
| 相关产品： | 576-3787-ND - IC ETHERNET SW 4PORT 64QFN |
| 其它名称： | 576-3869 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页当前第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页
1997 Microchip Technology Inc.
DS30444E - page 43
PIC16C9XX
6.0
OVERVIEW OF TIMER
MODULES
Each module can generate an interrupt to indicate that
an event has occurred (e.g. timer overow). Each of
these modules is explained in full detail in the following
sections. The timer modules are:
Timer0 Module (Section 7.0)
Timer1 Module (Section 8.0)
6.1
Timer0 Overview
The Timer0 module is a simple 8-bit timer/counter. The
clock source can be either the internal system clock
(Fosc/4) or an external clock. When the clock source is
an external clock, the Timer0 module can be selected
to increment on either the rising or falling edge.
The Timer0 module also has a programmable prescaler
option. This prescaler can be assigned to either the
Timer0 module or the Watchdog Timer. Bit PSA
(OPTION<3>) assigns the prescaler, and bits PS2:PS0
(OPTION<2:0>) determine the prescaler value. Timer0
can increment at the following rates: 1:1 when pres-
caler assigned to Watchdog timer, 1:2, 1:4, 1:8, 1:16,
1:32, 1:64, 1:128, and 1:256.
Synchronization of the external clock occurs after the
prescaler. When the prescaler is used, the external
clock frequency may be higher then the device’s fre-
quency. The maximum frequency is 50 MHz, given the
high and low time requirements of the clock.
6.2
Timer1 Overview
Timer1 is a 16-bit timer/counter. The clock source can
be either the internal system clock (Fosc/4), an external
clock, or an external crystal. Timer1 can operate as
either a timer or a counter. When operating as a counter
(external clock source), the counter can either operate
synchronized to the device or asynchronously to the
device. Asynchronous operation allows Timer1 to oper-
ate during sleep, which is useful for applications that
require a real-time clock as well as the power savings
of SLEEP mode.
Timer1 also has a prescaler option which allows Timer1
to increment at the following rates: 1:1, 1:2, 1:4, and
1:8. Timer1 can be used in conjunction with the Cap-
ture/Compare/PWM module. When used with a CCP
module, Timer1 is the time-base for 16-bit capture or
the 16-bit compare and must be synchronized to the
device. Timer1 oscillator is also one of the clock
sources for the LCD module.
6.3
Timer2 Overview
Timer2 is an 8-bit timer with a programmable prescaler
and postscaler, as well as an 8-bit period register
(PR2). Timer2 can be used with the CCP1 module (in
PWM mode) as well as the clock source for the Syn-
chronous Serial Port (SSP). The prescaler option
allows Timer2 to increment at the following rates: 1:1,
1:4, 1:16.
The postscaler allows the TMR2 register to match the
period register (PR2) a programmable number of times
before generating an interrupt. The postscaler can be
programmed from 1:1 to 1:16 (inclusive).
6.4
CCP Overview
The CCP module can operate in one of these three
modes: 16-bit capture, 16-bit compare, or up to 10-bit
Pulse Width Modulation (PWM).
Capture mode captures the 16-bit value of TMR1 into
the CCPR1H:CCPR1L register pair. The capture event
can be programmed for either the falling edge, rising
edge, fourth rising edge, or the sixteenth rising edge of
the CCP1 pin.
Compare mode compares the TMR1H:TMR1L register
pair to the CCPR1H:CCPR1L register pair. When a
match occurs an interrupt can be generated, and the
output pin CCP1 can be forced to given state (High or
Low), TMR1 can be reset and start A/D conversion.
This depends on the control bits CCP1M3:CCP1M0.
PWM mode compares the TMR2 register to a 10-bit
duty cycle register (CCPR1H:CCPR1L<5:4>) as well
as to an 8-bit period register (PR2). When the TMR2
register = Duty Cycle register, the CCP1 pin will be
forced low. When TMR2 = PR2, TMR2 is cleared to 00h,
an interrupt can be generated, and the CCP1 pin (if an
output) will be forced high.
相关PDF资料 |
PDF描述 |
|---|---|
| 362A024-3/42-0 | BOOT MOLDED |
| 0210391088 | CABLE JUMPER 1MM .203M 37POS |
| 570-002-744-200 | ASSEMBLY RECEPT 2 POS WATERPROOF |
| 202D285-4/42-0 | BOOT MOLDED |
| 0210391087 | CABLE JUMPER 1MM .178M 37POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8864RMNI | 功能描述:以太网 IC 4-Port 10/100 Ethernet Switch w/ 2x PHYs and 2x MAC Interface - Industrial Temp RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8864RMNU | 功能描述:以太网 IC 4-Port 10/100BT Switch with MII/RMII (Automotive) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8864RMNU TR | 制造商:Micrel Inc 功能描述:IC ETHERNET SWITCH 4PORT 64MLF |
| KSZ8873FLL | 功能描述:以太网 IC 3-Port Fast Ethernet Switch with 2x FX Ports - Lead free RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8873FLL-EVAL | 功能描述:以太网开发工具 3-Port Fast Ethernet Switch with 2x FX Ports - Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。