- 您现在的位置：买卖IC网 > PDF目录16826 > KSZ8864RMN-EVAL (Micrel Inc)BOARD EVALUATION FOR KSZ8864RMN PDF资料下载
参数资料
| 型号： | KSZ8864RMN-EVAL |
| 厂商： | Micrel Inc |
| 文件页数： | 84/111页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR KSZ8864RMN |
| 标准包装： | 1 |
| 主要目的： | 接口，以太网控制器（PHY 和 MAC） |
| 嵌入式： | 否 |
| 已用 IC / 零件： | KSZ8864RMN |
| 已供物品： | 板 |
| 相关产品： | 576-3787-ND - IC ETHERNET SW 4PORT 64QFN |
| 其它名称： | 576-3869 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页当前第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页
PIC16C9XX
DS30444E - page 74
1997 Microchip Technology Inc.
11.3.1
SLAVE MODE
In slave mode, the SCL and SDA pins must be cong-
ured as inputs (TRISC<4:3> set). The SSP module will
override the input state with the output data when
required (slave-transmitter).
When an address is matched or the data transfer after
an address match is received, the hardware automati-
cally will generate the acknowledge (ACK) pulse, and
then load the SSPBUF register with the received value
currently in the SSPSR register.
There are certain conditions that will cause the SSP
module not to give this ACK pulse. These are if either
(or both):
a)
The buffer full bit BF (SSPSTAT<0>) was set
before the transfer was received.
b)
The overow bit SSPOV (SSPCON<6>) was set
before the transfer was received.
In this case, the SSPSR register value is not loaded into
the SSPBUF, but bit SSPIF (PIR1<3>) is set. Table 11-3
shows what happens when a data transfer byte is
received, given the status of bits BF and SSPOV. The
shaded cells show the condition where user software
did not properly clear the overow condition. Flag bit BF
is cleared by reading the SSPBUF register while bit
SSPOV is cleared through software.
The SCL clock input must have a minimum high and
low time for proper operation. The high and low times of
the I2C specication as well as the requirement of the
SSP module is shown in timing parameter #100 and
parameter #101.
11.3.1.1
ADDRESSING
Once the SSP module has been enabled, it waits for a
START condition to occur. Following the START condi-
tion, the 8-bits are shifted into the SSPSR register. All
incoming bits are sampled with the rising edge of the
clock (SCL) line. The value of register SSPSR<7:1> is
compared to the value of the SSPADD register. The
address is compared on the falling edge of the eighth
clock (SCL) pulse. If the addresses match, and the BF
and SSPOV bits are clear, the following events occur:
a)
The SSPSR register value is loaded into the
SSPBUF register.
b)
The buffer full bit, BF is set.
c)
An ACK pulse is generated.
d)
SSP interrupt ag bit, SSPIF (PIR1<3>) is set
(interrupt is generated if enabled) - on the falling
edge of the ninth SCL pulse.
In 10-bit address mode, two address bytes need to be
received by the slave (Figure 11-10). The ve Most Sig-
nicant bits (MSbs) of the rst address byte specify if
this is a 10-bit address. Bit R/W (SSPSTAT<2>) must
specify a write so the slave device will receive the sec-
ond address byte. For a 10-bit address the rst byte
would equal ‘1111 0 A9 A8 0’, where A9 and A8 are
the two MSbs of the address. The sequence of events
for a 10-bit address is as follows, with steps 7- 9 for
slave-transmitter:
1.
Receive rst (high) byte of Address (bits SSPIF,
BF, and bit UA (SSPSTAT<1>) are set).
2.
Update the SSPADD register with second (low)
byte of Address (clears bit UA and releases the
SCL line).
3.
Read the SSPBUF register (clears bit BF) and
clear ag bit SSPIF.
4.
Receive second (low) byte of Address (bits
SSPIF, BF, and UA are set).
5.
Update the SSPADD register with the rst (high)
byte of Address, if match releases SCL line, this
will clear bit UA.
6.
Read the SSPBUF register (clears bit BF) and
clear ag bit SSPIF.
7.
Receive repeated START condition.
8.
Receive rst (high) byte of Address (bits SSPIF
and BF are set).
9.
Read the SSPBUF register (clears bit BF) and
clear ag bit SSPIF.
TABLE 11-3: DATA TRANSFER RECEIVED BYTE ACTIONS
Status Bits as Data
Transfer is Received
SSPSR
→ SSPBUF
Generate ACK
Pulse
Set bit SSPIF
(SSP Interrupt occurs
if enabled)
BF
SSPOV
0
Yes
1
0
No
Yes
1
No
Yes
0
1
No
Yes
相关PDF资料 |
PDF描述 |
|---|---|
| 362A024-3/42-0 | BOOT MOLDED |
| 0210391088 | CABLE JUMPER 1MM .203M 37POS |
| 570-002-744-200 | ASSEMBLY RECEPT 2 POS WATERPROOF |
| 202D285-4/42-0 | BOOT MOLDED |
| 0210391087 | CABLE JUMPER 1MM .178M 37POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8864RMNI | 功能描述:以太网 IC 4-Port 10/100 Ethernet Switch w/ 2x PHYs and 2x MAC Interface - Industrial Temp RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8864RMNU | 功能描述:以太网 IC 4-Port 10/100BT Switch with MII/RMII (Automotive) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8864RMNU TR | 制造商:Micrel Inc 功能描述:IC ETHERNET SWITCH 4PORT 64MLF |
| KSZ8873FLL | 功能描述:以太网 IC 3-Port Fast Ethernet Switch with 2x FX Ports - Lead free RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8873FLL-EVAL | 功能描述:以太网开发工具 3-Port Fast Ethernet Switch with 2x FX Ports - Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。