- 您现在的位置：买卖IC网 > PDF目录15309 > LTC1735CGN-1#TRPBF (Linear Technology)IC REG CTRLR BUCK PWM CM 16-SSOP PDF资料下载
参数资料
| 型号： | LTC1735CGN-1#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 20/28页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 16-SSOP |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 335kHz |
| 占空比： | 99.4% |
| 电源电压： | 3.5 V ~ 30 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 85°C |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC1735-1
APPLICATIO S I FOR ATIO
Other “hidden” losses such as copper trace and internal
battery resistances can account for an additional 5% to
10% efficiency degradation in portable systems. It is very
important to include these “system” level losses in the
design of a system. The internal battery and fuse resistance
losses can be minimized by making sure that C IN has
adequate charge storage and a very low ESR at the
switching frequency. A 25W supply will typically require
a minimum of 20 μ F to 40 μ F of capacitance having a
maximum of 0.01 ? to 0.02 ? of ESR. Other losses
including Schottky conduction losses during dead-time
and inductor core losses generally account for less than
2% total additional loss.
Checking Transient Response
The regulator loop response can be checked by looking at
the load current transient response. Switching regulators
take several cycles to respond to a step in DC (resistive)
load current. When a load step occurs, V OUT shifts by an
amount equal to ? I LOAD (ESR), where ESR is the effective
series resistance of C OUT . ? I LOAD also begins to charge or
discharge C OUT generating the feedback error signal that
forces the regulator to adapt to the current change and
return V OUT to its steady-state value. During this recovery
time V OUT can be monitored for excessive overshoot or
ringing, which would indicate a stability problem.
OPTI-LOOP compensation allows the transient response
to be optimized over a wide range of output capacitance
and ESR values. The availability of the I TH pin not only
allows optimization of control loop behavior but also
provides a DC coupled and AC filtered closed-loop response
test point. The DC step, rise time and settling at this test
point truly reflects the closed loop response. Assuming a
predominantly second order system, phase margin and/or
damping factor can be estimated using the percentage of
overshoot seen at this pin. The bandwidth can also be
estimated by examining the rise time at the pin. The I TH
external components shown in the Figure 1 circuit will
provide an adequate starting point for most applications.
The I TH series R C -C C filter sets the dominant pole-zero
loop compensation. The values can be modified slightly
(from 0.5 to 2 times their suggested values) to optimize
transient response once the final PC layout is done and the
particular output capacitor type and value have been
20
determined. The output capacitors need to be decided
upon because the various types and values determine the
loop feedback factor gain and phase. An output current
pulse of 20% to 100% of full load current having a rise time
of 1 μ s to 10 μ s will produce output voltage and I TH pin
waveforms that will give a sense of the overall loop
stability without breaking the feedback loop. The initial
output voltage step may not be within the bandwidth of the
feedback loop, so the standard second order overshoot/
DC ratio cannot be used to determine phase margin. The
gain of the loop will be increased by increasing R C and the
bandwidth of the loop will be increased by decreasing C C .
If R C is increased by the same factor that C C is decreased,
the zero frequency will be kept the same, thereby keeping
the phase shift the same in the most critical frequency
range of the feedback loop. The output voltage settling
behavior is related to the stability of the closed-loop
system and will demonstrate the actual overall supply
performance. For a detailed explanation of optimizing the
compensation components, including a review of control
loop theory, refer to Application Note 76.
Improve Transient Response and Reduce Output
Capacitance with Active Voltage Positioning
Fast load transient response, limited board space and low
cost are normal requirements of microprocessor power
supplies. Active voltage positioning improves transient
response and reduces the output capacitance required to
power a microprocessor where a typical load step can be
from 0.2A to 15A in 100ns or 15A to 0.2A in 100ns. The
voltage at the microprocessor must be held to about
± 0.1V of nominal in spite of these load current steps.
Since the control loop cannot respond this fast, the output
capacitors must supply the load current until the control
loop can respond. Capacitor ESR and ESL primarily deter-
mine the amount of droop or overshoot in the output
voltage. Normally, several capacitors in parallel are re-
quired to meet microprocessor transient requirements.
Active voltage positioning is a form of deregulation. It
sets the output voltage high for light loads and low for
heavy loads. When load current suddenly increases, the
output voltage starts from a level higher than nominal so
the output voltage can droop more and stay within the
specified voltage range. When load current suddenly
相关PDF资料 |
PDF描述 |
|---|---|
| UPS2E470MHD | CAP ALUM 47UF 250V 20% RADIAL |
| RBC20DRYI-S734 | CONN EDGECARD 40POS DIP .100 SLD |
| UPM2E330MHD1TN | CAP ALUM 33UF 250V 20% RADIAL |
| VI-2WD-EW-F2 | CONVERTER MOD DC/DC 85V 100W |
| VI-JWN-EW-F4 | CONVERTER MOD DC/DC 18.5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1735CGNPBF | 制造商:Linear Technology 功能描述:Regulator Synch Step Down LTC1735CGN |
| LTC1735CS | 功能描述:IC REG CTRLR BUCK PWM CM 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1735CS#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC1735CS#TR | 功能描述:IC REG CTRLR BUCK PWM CM 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1735CS#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。