- 您现在的位置：买卖IC网 > PDF目录369885 > LXT350PE PCM TRANSCEIVER|SINGLE|CEPT PCM-30/E-1|CMOS|LDCC|28PIN|PLASTIC PDF资料下载
参数资料
| 型号： | LXT350PE |
| 英文描述： | PCM TRANSCEIVER|SINGLE|CEPT PCM-30/E-1|CMOS|LDCC|28PIN|PLASTIC |
| 中文描述： | 的PCM收发器|单|优税PCM-30/E-1 |的CMOS | LDCC | 28脚|塑料 |
| 文件页数： | 14/50页 |
| 文件大小： | 1197K |
| 代理商： | LXT350PE |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
LXT350
—
T1/E1 Short Haul Transceiver with Crystal-less Jitter Attenuation
14
Datasheet
2.0
Functional Description
The LXT350 is a fully integrated, PCM transceiver for short-haul, 1.544 Mbps (T1) or 2.048 Mbps
(E1) applications allowing full-duplex transmission of digital data over existing twisted-pair
installations. It interfaces with two twisted-pair lines (one pair each for transmit and receive)
through standard pulse transformers and appropriate resistors.
The figure on the front page of this data sheet shows a block diagram of the LXT350. The designer
can configure the device for either Host or Hardware control. In Host mode, control is via the serial
microprocessor port. In Hardware mode, individual pin settings allow stand-alone operation.
The transceiver provides a high-precision, crystal-less jitter attenuator. The user may place it in the
transmit or receive path, or bypass it completely.
The LXT350 meets or exceeds FCC, ANSI T1 and AT&T specifications for CSU and DSX-1
applications, as well as ITU and ETSI requirements for E1 ISDN PRI applications.
2.1
Initialization
During power up, the transceiver remains static until the power supply reaches approximately 3 V.
Upon crossing this threshold, the device begins a 32 ms reset cycle to calibrate the Phase Lock
Loops (PLL). The transceiver uses a reference clock to calibrate the PLLs: the transmitter reference
is TCLK, and the receiver reference clock is MCLK. MCLK is mandatory for chip operation and
must be an independent free running jitter free reference clock.
2.1.1
Reset Operation
A reset operation initializes the status and state machines for the LOS, AIS, and QRSS blocks. In
Hardware mode, holding pins RLOOP, LLOOP and TAOS High for at least one clock cycle resets
the device. In Host mode, writing a 1 to the bit CR2.RESET commands a reset which clears all
registers to 0. Allow 32 ms for the device to settle after removing all reset conditions.
2.2
Transmitter
2.2.1
Transmit Digital Data Interface
Input data for transmission onto the line is clocked serially into the device at the TCLK rate. TPOS
and TNEG are the bipolar data inputs. In Unipolar mode, the TDATA pin accepts unipolar data.
Input data may pass through either the Jitter Attenuator or B8ZS/HDB3 encoder or both. In Host
mode, setting CR1.ENCENB = 1 enables B8ZS/HDB3 encoding. In Hardware mode, connecting
the MODE pin to Midrange selects zero suppression coding. With zero suppression enabled, the
EC1 through EC3 inputs determine the coding scheme as listed in
Table 10 on page 29
.
TCLK supplies input synchronization. See the
Figure 16 on page 43
for the transmit timing
requirements for TCLK and the Master Clock (MCLK).
相关PDF资料 |
PDF描述 |
|---|---|
| LXT361LE | Telecommunication IC |
| LXT361PE | Telecommunication IC |
| LXT362LE | PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|QFP|44PIN|PLASTIC |
| LXT362PE | PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|LDCC|28PIN|PLASTIC |
| LXT362QE | PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|QFP|44PIN|PLASTIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LXT350QE | 制造商:LEVEL1 功能描述: |
| LXT351 | 制造商:INTEL 制造商全称:Intel Corporation 功能描述:T1/E1 Short Haul Transceiver with Crystal-less Jitter Attenuation |
| LXT351PE | 制造商:INTEL 制造商全称:Intel Corporation 功能描述:PCM TRANSCEIVER|SINGLE|CEPT PCM-30/E-1|CMOS|LDCC|28PIN|PLASTIC |
| LXT351QE | 制造商:INTEL 制造商全称:Intel Corporation 功能描述:PCM TRANSCEIVER|SINGLE|CEPT PCM-30/E-1|CMOS|QFP|44PIN|PLASTIC |
| LXT360 | 制造商:LVL1 制造商全称:LVL1 功能描述:Integrated T1/E1 LH/SH Transceivers for DS1/DSX-1/CSU or NTU/ISDN PRI Applications |
发布紧急采购，3分钟左右您将得到回复。