- 您现在的位置：买卖IC网 > PDF目录180126 > M306V8FJFP 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP116 PDF资料下载
参数资料
| 型号： | M306V8FJFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP116 |
| 封装： | 20 X 20 MM, 0.65 MM PITCH, PLASTIC, LQFP-116 |
| 文件页数： | 62/77页 |
| 文件大小： | 2650K |
| 代理商： | M306V8FJFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页当前第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页
M306V8FJFP
Rev.1.31
Apr 18, 2005
page 63 of 363
REJ03B0082-0131
(3) Stop Mode
In stop mode, all oscillator circuits are turned off, so are the CPU clock and the peripheral function clocks.
Therefore, the CPU and the peripheral functions clocked by these clocks stop operating. The least
amount of power is consumed in this mode.
However, the peripheral functions clocked by external signals keep operating. The following interrupts
can be used to exit stop mode.
Key interrupt
______
INT interrupt
Timer A, Timer B interrupt (when counting external pulses in event counter mode)
Serial I/O interrupt (when external clock is selected)
Entering Stop Mode
The microcomputer is placed into stop mode by setting the CM10 bit of CM1 register to “1” (all clocks
turned off). At the same time, the CM06 bit of CM0 register is set to “1” (divide-by-8 mode) and the
CM15 bit of CM1 register is set to “1” (main clock oscillator circuit drive capability high).
Pin Status in Stop Mode
Table 5.5 lists pin status during stop mode
Exiting Stop Mode
The microcomputer is moved out of stop mode by a hardware reset, or peripheral function interrupt.
If the microcomputer is to be moved out of stop mode by a hardware reset or, set the peripheral
function interrupt priority ILVL2 to ILVL0 bits to “0002” (interrupts disable) before setting the CM10 bit
to “1”.
If the microcomputer is to be moved out of stop mode by a peripheral function interrupt, set up the
following before setting the CM10 bit to “1”.
1. In the ILVL2 to ILVL0 bits of interrupt control register, set the interrupt priority level of the periph-
eral function interrupt to be used to exit stop mode.
Also, for all of the peripheral function interrupts not used to exit stop mode, set the ILVL2 to ILVL0
bits to “0002”.
2. Set the I flag to “1”.
3. Enable the peripheral function whose interrupt is to be used to exit stop mode.
In this case, when an interrupt request is generated and the CPU clock is thereby turned on, an
interrupt service routine is executed.
Which CPU clock will be used after exiting stop mode by a peripheral function is determined by the
CPU clock that was on when the microcomputer was placed into stop mode as follows:
If the CPU clock before entering stop mode was derived from the sub clock: sub clock
If the CPU clock before entering stop mode was derived from the main clock: main clock divide-by-8
相关PDF资料 |
PDF描述 |
|---|---|
| M30L40C-E3/4W | 15 A, 40 V, SILICON, RECTIFIER DIODE, TO-220AB |
| M31022AGLJFREQ | VCXO, CLOCK, 150 MHz - 1400 MHz, LVDS OUTPUT |
| M31002AMPJFREQ | VCXO, CLOCK, 150 MHz - 1400 MHz, PECL OUTPUT |
| M31022BGLNFREQ | VCXO, CLOCK, 150 MHz - 1400 MHz, LVDS OUTPUT |
| M31026ASLJFREQ | VCXO, CLOCK, 150 MHz - 1400 MHz, LVDS OUTPUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M3-076 | 制造商:Southco 功能描述: |
| M3077 | 制造商:Tamura Corporation of America 功能描述: |
| M30800FCFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30800FCFP#U3 | 功能描述:MCU 3/5V 128K I-TEMP PB-FREE 100 RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:M16C™ M16C/80 标准包装:160 系列:S08 核心处理器:S08 芯体尺寸:8-位 速度:40MHz 连通性:I²C，LIN，SCI，SPI 外围设备:LCD，LVD，POR，PWM，WDT 输入/输出数:53 程序存储器容量:32KB（32K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1.9K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 12x12b 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:64-LQFP 包装:托盘 |
| M30800FCGP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。