- 您现在的位置：买卖IC网 > PDF目录18820 > MAX11008BETM+ (Maxim Integrated)IC CTLR LDMOS BIAS DUAL 48TQFN PDF资料下载
参数资料
| 型号： | MAX11008BETM+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 29/67页 |
| 文件大小： | 0K |
| 描述： | IC CTLR LDMOS BIAS DUAL 48TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 43 |
| 功能： | 偏压控制器 |
| RF 型： | 手机 |
| 次要属性： | 片上 4Kb EEPROM |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
Dual RF LDMOS Bias Controller with
Nonvolatile Memory
ADC and DAC References
The MAX11008 provides an internal low-noise +2.5V
reference for the ADCs, DACs and temperature sensor.
When using the internal reference the REFDAC and
REFADC inputs can either be left open or to improve
noise performance, bypassed with a 0.1μF capacitor to
AGND. Connect a voltage source to the REFADC input
ranging between +1V to AV DD to configure the device
for external ADC reference mode. Connect a voltage
source to the REFDAC input ranging between +0.7V to
+2.5V to configure the device for external DAC refer-
ence mode. When using an external voltage reference,
bypass the REFDAC and REFADC inputs with a 0.1μF
capacitor to AGND. Bits D[3:0] within the Hardware
Configuration register control the source of the DAC
and ADC references. See Table 11.
Temperature Sensors
The MAX11008 measures the internal die temperature
and two external LDMOS transistor temperatures through
one internal and two external diode-connected transis-
tors. The MAX11008 performs temperature measure-
ments by changing the bias current of each diode from
4μA to 68μA to produce a temperature-dependent bias
voltage difference. The internal ADC converts the volt-
age difference to a digital value. The conversion result at
4μA is subtracted from the conversion results at 68μA to
calculate a digital value that is proportional to absolute
temperature. The output data sent to the master will be
the resultant digital code minus an offset value to adjust
from Kelvin to Celsius. Temperature data is delivered to
the master as a 12-bit signed (two’s complement) frac-
tional number with the 3 LSBs being the fractional bits.
This provides a temperature measurement resolution of
1/8°C. See Table 3 for examples of the signed fractional
number digital temperature codes.
Table 3. Signed Fractional Number
Temperature-Code Examples
In clock mode 00, initiate temperature conversions by
writing 0x13 to the ADC Conversion register. In clock
mode 01, initiate temperature conversions by writing
0x13 to the ADC Conversion register and pulse CNVST
low. In clock mode 11, initiate temperature conversions
by writing 0x13 to the ADC Conversion register and
pulse CNVST low for each channel conversion. Set the
corresponding data bits for the temperature sensor to
be measured to 1 (see the ADC Conversion Register
(ADCCON) (Write Only) section and Table 20) for all
three clock modes. Set the high and low external tem-
perature thresholds through the temperature threshold
registers. See the Low Temperature Threshold
Registers (TL1, TL2) (Read/Write) section, High
Temperature Threshold Registers (TH1, TH2)
(Read/Write) section, and Tables 7 and 8).
The reference voltage for the temperature measure-
ments is always derived from the internal reference
source to ensure that 1 LSB corresponds to 1/8 of a
degree Celsius. On every scan where only temperature
measurements are requested, temperature conversions
are carried out in the following order: INTEMP,
EXTEMP1, then EXTEMP2. If the ADCMON bit is set
when the conversions are performed, the temperature
readings are available in the FIFO.
The temperature-sensing circuits power up at the start
of an ADC conversion scan. The temperature-sensing
circuits remain powered on until the end of the scan to
avoid a 50μs delay caused by the internal reference
power-up time required for each individual temperature
channel. The temperature-sensor circuits remain pow-
ered up when the ADC conversion register’s continu-
ous convert bit (CONCONV, see Table 20) is set to 1
and the current ADC conversion includes a tempera-
ture channel. The temperature-sensor circuits remain
powered up until the CONCONV bit is set low.
The external temperature-sensor drive current ratio has
been optimized for a 2N3904 npn transistor with an ide-
ality factor of 1.0065. The nonideality offset is removed
TEMPERATURE
(°C)
-40
-1.625
0
+27.125
+105
DIGITAL CODE
[D11:0]
1110 1100 0000
1111 1111 0011
0000 0000 0000
0000 1101 1001
0011 0100 1000
internally by a preset digital coefficient. Using a transis-
tor with a different ideality factor produces a proportion-
ate difference in the absolute measured temperature.
For more details on this topic and others related to
using an external temperature sensor, refer to
Application Note 1057: Compensating for Ideality
Factor and Series Resistance Differences between
Thermal Sense Diodes and Application Note 1944:
Temperature Monitoring Using the MAX1253/54 and
MAX1153/54.
______________________________________________________________________________________
29
相关PDF资料 |
PDF描述 |
|---|---|
| MCD310-16IO1 | MOD THYRISTOR/DIODE 1600V Y2-DCB |
| AH173-WL-7-B | IC HALL SENSOR LATCH 25MA SC59-3 |
| ACH3218-151-TD01 | FILTER 3-TERM 240MHZ 1.5A SMD |
| ND431425 | SCR MOD ISO DUAL 1400V 250A |
| AH175-WL-7-B | IC HALL SENSOR LATCH 25MA SC59-3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX11008BETM+ | 功能描述:射频放大器 Dual RF LDMOS Bias Controller w/NV Mem RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| MAX11008BETM+T | 功能描述:射频放大器 Dual RF LDMOS Bias Controller w/NV Mem RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| MAX11008EVC16 | 功能描述:放大器 IC 开发工具 MAX11008 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| MAX11008EVKIT+ | 功能描述:放大器 IC 开发工具 MAX11008 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| MAX1100CWG | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。