- 您现在的位置：买卖IC网 > PDF目录18820 > MAX11008BETM+ (Maxim Integrated)IC CTLR LDMOS BIAS DUAL 48TQFN PDF资料下载
参数资料
| 型号： | MAX11008BETM+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 34/67页 |
| 文件大小： | 0K |
| 描述： | IC CTLR LDMOS BIAS DUAL 48TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 43 |
| 功能： | 偏压控制器 |
| RF 型： | 手机 |
| 次要属性： | 片上 4Kb EEPROM |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
Dual RF LDMOS Bias Controller with
Nonvolatile Memory
high until the current scan is complete and the ADC
sequence halts. In single-conversion mode (CKSEL1,
CKSEL0 = 11), the BUSY signal remains high until the
ADC has completed the current conversion (not the
entire scan), the data has been moved into the FIFO,
and the alarm limits for the channel have been checked
(if alarm is enabled).
Alarm Function
The MAX11008 features a multipurpose alarm function
that indicates when a temperature sensor or a current-
sense amplifier reading exceeds the threshold values
specified in the High Temperature Threshold, Low
Temperature Threshold, High Current Threshold, and
Low Current Threshold registers (see Tables 7 to 10).
The thresholds for each temperature sensor and cur-
rent-sense amplifier channel are set individually and
can be configured to operate in window mode or hys-
teresis mode (see the Window Mode and Hysteresis
Mode sections). Alarm indication is provided by the
ALARM output while information on the source of the
alarm is contained in the Flag register (see Table 26).
The enabling of the various alarms, the polarity of the
ALARM output (active-high or active-low), the ALARM-
output modes, the alarm-threshold modes, and the
methods by which the MAX11008 services an alarm are
controlled with the Alarm Software Configuration regis-
ter and Alarm Hardware Configuration register (see
Tables 12 and 14).
ALARM-Output Modes
The ALARM output operates in comparator mode or
interrupt mode based on the setting of the ACOMP bit
(D8) in the Alarm Hardware Configuration register (see
Table 14).
When configured for comparator mode, the ALARM
output is asserted when the measured current or tem-
perature value exceeds the set threshold level and is
deasserted when the value returns below the set
threshold level.
When configured for interrupt mode, the ALARM output
is asserted when the measured current/temperature
value exceeds the set threshold level and remains
asserted until the Flag register is read, at which time
the ALARM output is deasserted. The alarm output is
only asserted again if the alarm channel recovers and
then re-trips (or if a different alarm channel trips).
See Figures 19 and 20 for examples of both ALARM-
output modes.
Window Mode
Set the TWIN1 bit (D2) or TWIN2 bit (D6) to 1 in the
Alarm Software Configuration register (see Table 12) to
configure the temperature alarm thresholds for channel 1
or channel 2 to window mode. Set the IWIN1 bit (D0) or
IWIN2 bit (D4) to 1 in the Alarm Software Configuration
register to set the current alarm thresholds for channel 1
or channel 2 to window mode. In window mode, temper-
ature/current measurements are compared to the set
temperature/current high and low thresholds. If a mea-
sured value is outside the configured window values
(between the set high and low thresholds) and that cor-
responding channel is configured to cause an alarm
condition, the alarm asserts. The alarm remains internally
asserted until the measured values from that channel fall
back into the window and past the configurable hystere-
sis. The external behavior of ALARM and the gate
clamps are controlled by the settings of the ACOMP and
ALMCLMP_ bits in the Alarm Hardware Configuration
register. The amount of built-in hysteresis can be varied
from 8 LSBs to 64 LSBs by setting ALMHYST[1:0] bits
(D6 and D7) in the Alarm Hardware Configuration regis-
ter (see Tables 14 and 14a). See Figures 19 and 20 for
window-mode threshold examples.
Hysteresis Mode
Set the TWIN1 bit (D2) or TWIN2 bit (D6) to 0 in the
Alarm Software Configuration register (see Table 12) to
set the temperature alarm thresholds for channel 1 or
channel 2 to hysteresis mode. Set the IWIN1 bit (D0) or
IWIN2 bit (D4) to 0 to set the current alarm thresholds
for channel 1 or channel 2 to hysteresis mode. In hys-
teresis mode, temperature or current measurements
are compared to the set temperature/current high and
low thresholds. If a measured value is above the set
high threshold and the corresponding channel is con-
figured to cause an alarm condition, the alarm asserts.
ALARM remains internally asserted until the measured
values from that channel fall back below the low thresh-
old setting. The external behavior of ALARM and the
gate clamps are controlled by the settings of the
ACOMP and ALMCLMP_ bits in the Alarm Hardware
Configuration register. See Figures 21 and 22 for hys-
teresis-mode threshold examples.
V GATE _ Output Equation
Based on the monitored LDMOS current analog input
voltage and temperature values, the MAX11008 logically
decides if the calculated bias voltage, V GATE_ , driving the
gate of the RF LDMOS, should be recalculated and
adjusted to maintain the desired RF LDMOS drain cur-
rent. The MAX11008 independently monitors and calcu-
lates the V GATE_ voltage for both channel 1 and channel
2. The MAX11008 implements the following equation
when calculating V GATE_ for each DAC channel:
34
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MCD310-16IO1 | MOD THYRISTOR/DIODE 1600V Y2-DCB |
| AH173-WL-7-B | IC HALL SENSOR LATCH 25MA SC59-3 |
| ACH3218-151-TD01 | FILTER 3-TERM 240MHZ 1.5A SMD |
| ND431425 | SCR MOD ISO DUAL 1400V 250A |
| AH175-WL-7-B | IC HALL SENSOR LATCH 25MA SC59-3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX11008BETM+ | 功能描述:射频放大器 Dual RF LDMOS Bias Controller w/NV Mem RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| MAX11008BETM+T | 功能描述:射频放大器 Dual RF LDMOS Bias Controller w/NV Mem RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| MAX11008EVC16 | 功能描述:放大器 IC 开发工具 MAX11008 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| MAX11008EVKIT+ | 功能描述:放大器 IC 开发工具 MAX11008 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| MAX1100CWG | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。