- 您现在的位置：买卖IC网 > PDF目录1837 > MAX16068ETI+T (Maxim Integrated Products)IC SYSTEM MANAGER 6CH 28-TQFN PDF资料下载
参数资料
| 型号： | MAX16068ETI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/41页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM MANAGER 6CH 28-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 六路电源监控器 |
| 电源电压： | 2.8 V ~ 14 V |
| 电流 - 电源： | 2.8mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
6-Channel, Flash-Configurable System Manager
with Nonvolatile Fault Registers
Detailed Description
The MAX16068 monitors up to six system power sup-
plies. The monitoring phase begins after boot-up if EN is
high and the software enable bit is set to ‘1’. An internal
multiplexer cycles through each MON_ input. At each
multiplexer stop, the 10-bit ADC converts the monitored
analog voltage to a digital result and stores the result in
a register. Each time a conversion cycle (5 F s, max) com-
pletes, internal logic circuitry compares the conversion
results to the overvoltage and undervoltage thresholds
stored in memory. When a result violates a programmed
threshold, the conversion can be configured to generate
a fault. GPIO_ can be programmed to assert on combi-
nations of faults. Additionally, faults can be configured to
trigger the nonvolatile fault logger, which writes all fault
information automatically to the flash and write-protects
the data to prevent accidental erasure.
The MAX16068 contains both SMBus and JTAG serial
interfaces for accessing registers and flash. Use only
one interface at any given time. For more information
on how to access the internal memory through these
interfaces, see the SMBus-Compatible Serial Interface
and JTAG Serial Interface sections. The memory map
is divided into three pages with access controlled by
special SMBus and JTAG commands.
The factory-default values at POR (power-on reset) for all
RAM registers are ‘0’s. POR occurs when V CC reaches
the undervoltage-lockout threshold (UVLO) of 2.7V
(max). At POR, the device begins a boot-up sequence.
During the boot-up sequence, all monitored inputs are
masked from initiating faults and flash contents are
copied to the respective register locations. During boot-
up, the MAX16068 is not accessible through the serial
Table 1. Software Enable Configurations
interface. The boot-up sequence takes up to 150 F s, after
which the device is ready for normal operation. RESET
is asserted low up to the boot-up phase after which it
assumes its programmed active state. RESET remains
active for its programmed timeout period once all moni-
tored channels are within their respective thresholds. Up
to the boot-up phase, the GPIO_s are high impedance.
Power
Apply 2.8V to 14V to V CC to power the MAX16068.
Bypass V CC to ground with a 10 F F capacitor. Two inter-
nal voltage regulators, ABP and DBP, supply power to
the analog and digital circuitry within the device. For
operation at 3.6V or lower, disable the regulators by con-
necting ABP and DBP to V CC .
ABP is a 3.0V (typ) voltage regulator that powers the inter-
nal analog circuitry. Bypass ABP to GND with a 1 F F ceram-
ic capacitor installed as close as possible to the device.
DBP is an internal 3.0V (typ) voltage regulator. DBP
powers flash and digital circuitry. All push-pull outputs
refer to DBP. DBP supplies the input voltage to the inter-
nal charge pump when the programmable outputs are
configured as charge-pump outputs. Bypass the DBP
output to GND with a 1 F F ceramic capacitor installed as
close as possible to the device.
Do not power external circuitry from ABP or DBP.
Enable Input (EN)
To enable monitoring, the voltage at EN must be above
1.24V (typ) and the software enable bit in r73h[0] must
be set to ‘1.’ To disable monitoring, either pull EN
below 1.215V (typ) or set the software enable bit to ‘0.’
See Table 1 for the software enable bit configurations.
Connect EN to ABP if not used.
REGISTER
ADDRESS
FLASH
ADDRESS
BIT RANGE
DESCRIPTION
Software Enable
[0]
[1]
1 = Sequencing enabled
0 = Power-down
Reserved
73h
273h
[2]
[3]
1 = Margin mode enabled
Reserved
Independent watchdog mode enable
[4]
1 = Watchdog timer is independent of EN input
0 = Watchdog timer boots after EN goes high and the boot-up delay completes
10
_____________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1606EUA | IC REG BOOST ADJ 0.5A 8UMAX |
| MAX16070ETL+T | IC SYSTEM MANAGER 12CH 40-TQFN |
| MAX16072RS16D0+T | IC MPU SUPERVISOR CIRCUIT 4UCSP |
| MAX1607ESA | IC SW CURRENT LIMITED USB 8-SOIC |
| MAX16125WTEJ00+T | IC PUSH BUTTON CTRLR 6WLP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16069FTC+ | 功能描述:监控电路 Quad/Hex/Octal Volt uP Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16069FTC+T | 功能描述:监控电路 Quad/Hex/Octal Volt uP Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX1606EUA | 功能描述:LCD 驱动器 28V Int Switch LCD Bias Supply RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX1606EUA.C71076 | 制造商:Maxim Integrated Products 功能描述: |
| MAX1606EUA+ | 功能描述:LCD 驱动器 28V Int Switch LCD Bias Supply RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。