- 您现在的位置：买卖IC网 > PDF目录1837 > MAX16068ETI+T (Maxim Integrated Products)IC SYSTEM MANAGER 6CH 28-TQFN PDF资料下载
参数资料
| 型号： | MAX16068ETI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/41页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM MANAGER 6CH 28-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 六路电源监控器 |
| 电源电压： | 2.8 V ~ 14 V |
| 电流 - 电源： | 2.8mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
6-Channel, Flash-Configurable System Manager
with Nonvolatile Fault Registers
When in the monitoring state, and when EN falls below
the undervoltage threshold, a register bit, ENRESET
(r20h[2]), is set to a ‘1.’ This register bit latches and must
be cleared through software. This bit indicates if RESET
is asserted low due to EN going under the threshold.
The POR state of ENRESET is ‘0.’ The bit is only set on a
falling edge of the EN comparator output or the software
enable bit. If operating in latch-on fault mode, toggle EN
or toggle the software enable bit to clear the latch condi-
tion and restart the device once the fault condition has
been removed.
Set r73h[2] to ‘1’ to enable monitoring functionality.
Faults are not recorded when the device is in margining
mode. Set r73h[2] to ‘0’ for normal functionality.
Voltage Monitoring
The MAX16068 features an internal 10-bit ADC that mon-
itors the MON_ voltage inputs. An internal multiplexer
cycles through each of the enabled inputs, taking less
than 24 F s for a complete monitoring cycle. Each acquisi-
tion takes approximately 4 F s. At each multiplexer stop,
the 10-bit ADC converts the analog input to a digital
result and stores the result in a register. ADC conversion
results are stored in registers r00h–r0Bh (see Table 2).
Use the SMBus or JTAG serial interface to read ADC
conversion results.
The MAX16068 provides six inputs, MON1–MON6, for
voltage monitoring. Each input-voltage range is pro-
grammable in registers r43h–r44h (see Table 3). When
Table 2. ADC Conversion Results (Read Only)
MON_ configuration registers are set to ’11,’ MON_ volt-
ages are not monitored and the multiplexer does not stop
at these inputs, decreasing the total cycle time. These
inputs cannot be configured to trigger fault conditions.
The two programmable thresholds for each monitored
voltage include an overvoltage and an undervoltage
threshold. See the Faults section for more information
on setting overvoltage and undervoltage thresholds. All
voltage thresholds are 8 bits wide. The 8 MSBs of the
10-bit ADC conversion result are compared to these
overvoltage and undervoltage thresholds.
For any undervoltage or overvoltage condition to be
monitored and any faults detected, the MON_ input must
be assigned to monitoring mode. Inputs that are not
enabled are not converted by the ADC; they contain the
last value acquired before that channel was disabled.
The ADC conversion result registers are reset to 00h at
boot-up. These registers are not reset when a reboot
command is executed.
To temporarily disable voltage monitoring during volt-
age margining conditions, set r73h[2] to ‘1’ to enable
margining mode functionality. Faults (except for faults
triggered by EXTFAULT being pulled low externally) are
not recorded when the device is in margining mode, but
the ADC continues to run and conversion results con-
tinue to be available. Set r73h[2] back to ‘0’ for normal
functionality.
REGISTER ADDRESS
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
BIT RANGE
[7:0]
[7:6]
[7:0]
[7:6]
[7:0]
[7:6]
[7:0]
[7:6]
[7:0]
[7:6]
[7:0]
[7:6]
MON1 result (MSB)
MON1 result (LSB)
MON2 result (MSB)
MON2 result (LSB)
MON3 result (MSB)
MON3 result (LSB)
MON4 result (MSB)
MON4 result (LSB)
MON5 result (MSB)
MON5 result (LSB)
MON6 result (MSB)
MON6 result (LSB)
DESCRIPTION
______________________________________________________________________________________
11
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1606EUA | IC REG BOOST ADJ 0.5A 8UMAX |
| MAX16070ETL+T | IC SYSTEM MANAGER 12CH 40-TQFN |
| MAX16072RS16D0+T | IC MPU SUPERVISOR CIRCUIT 4UCSP |
| MAX1607ESA | IC SW CURRENT LIMITED USB 8-SOIC |
| MAX16125WTEJ00+T | IC PUSH BUTTON CTRLR 6WLP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16069FTC+ | 功能描述:监控电路 Quad/Hex/Octal Volt uP Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16069FTC+T | 功能描述:监控电路 Quad/Hex/Octal Volt uP Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX1606EUA | 功能描述:LCD 驱动器 28V Int Switch LCD Bias Supply RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX1606EUA.C71076 | 制造商:Maxim Integrated Products 功能描述: |
| MAX1606EUA+ | 功能描述:LCD 驱动器 28V Int Switch LCD Bias Supply RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。