- 您现在的位置：买卖IC网 > PDF目录80585 > MB9AF312NPMC 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | MB9AF312NPMC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP100 |
| 封装： | 0.50 MM PITCH, PLASTIC, LQFP-100 |
| 文件页数： | 102/114页 |
| 文件大小： | 1357K |
| 代理商： | MB9AF312NPMC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页当前第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页
ATmega48PA/88PA/168PA [DATASHEET]
9223F–AVR–04/14
88
The Timer/Counter overflow flag (TOV0) is set each time the counter reaches TOP. If the interrupt is enabled, the interrupt
handler routine can be used for updating the compare value.
In fast PWM mode, the compare unit allows generation of PWM waveforms on the OC0x pins. Setting the COM0x1:0 bits to
two will produce a non-inverted PWM and an inverted PWM output can be generated by setting the COM0x1:0 to three:
Setting the COM0A1:0 bits to one allows the OC0A pin to toggle on compare matches if the WGM02 bit is set. This option is
not available for the OC0B pin (see Table 15-6 on page 93). The actual OC0x value will only be visible on the port pin if the
data direction for the port pin is set as output. The PWM waveform is generated by setting (or clearing) the OC0x register at
the compare match between OCR0x and TCNT0, and clearing (or setting) the OC0x register at the timer clock cycle the
counter is cleared (changes from TOP to BOTTOM).
The PWM frequency for the output can be calculated by the following equation:
The N variable represents the prescale factor (1, 8, 64, 256, or 1024).
The extreme values for the OCR0A register represents special cases when generating a PWM waveform output in the fast
PWM mode. If the OCR0A is set equal to BOTTOM, the output will be a narrow spike for each MAX+1 timer clock cycle.
Setting the OCR0A equal to MAX will result in a constantly high or low output (depending on the polarity of the output set by
the COM0A1:0 bits.)
A frequency (with 50% duty cycle) waveform output in fast PWM mode can be achieved by setting OC0x to toggle its logical
level on each compare match (COM0x1:0 = 1). The waveform generated will have a maximum frequency of fOC0 = fclk_I/O/2
when OCR0A is set to zero. This feature is similar to the OC0A toggle in CTC mode, except the double buffer feature of the
output compare unit is enabled in the fast PWM mode.
15.7.4 Phase Correct PWM Mode
The phase correct PWM mode (WGM02:0 = 1 or 5) provides a high resolution phase correct PWM waveform generation
option. The phase correct PWM mode is based on a dual-slope operation. The counter counts repeatedly from BOTTOM to
TOP and then from TOP to BOTTOM. TOP is defined as 0xFF when WGM2:0 = 1, and OCR0A when WGM2:0 = 5. In non-
inverting compare output mode, the output compare (OC0x) is cleared on the compare match between TCNT0 and OCR0x
while upcounting, and set on the compare match while downcounting. In inverting output compare mode, the operation is
inverted. The dual-slope operation has lower maximum operation frequency than single slope operation. However, due to
the symmetric feature of the dual-slope PWM modes, these modes are preferred for motor control applications.
In phase correct PWM mode the counter is incremented until the counter value matches TOP. When the counter reaches
TOP, it changes the count direction. The TCNT0 value will be equal to TOP for one timer clock cycle. The timing diagram for
the phase correct PWM mode is shown on Figure 15-7 on page 89. The TCNT0 value is in the timing diagram shown as a
histogram for illustrating the dual-slope operation. The diagram includes non-inverted and inverted PWM outputs. The small
horizontal line marks on the TCNT0 slopes represent compare matches between OCR0x and TCNT0.
fOCnxPWM
fclk_I/O
N 256
×
-------------------
=
相关PDF资料 |
PDF描述 |
|---|---|
| MB9AF315NPF | 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP100 |
| MSM65P514-JS | 8-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQCC68 |
| MSM67P620-JS | 16-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PQCC68 |
| MSM80C154-RS | 8-BIT, 12 MHz, MICROCONTROLLER, PDIP40 |
| MSM83C154-RS | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PDIP40 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB9AF314LAPMC1-G-JNE2 | 制造商:FUJITSU 功能描述: |
| MB9AF314LAPMC-G-JNE2 | 制造商:Fujitsu 功能描述:Bulk |
| MB9AF314LAQN-G-AVE2 | 功能描述:ARM? Cortex?-M3 FM3 MB9A310A Microcontroller IC 32-Bit 40MHz 256KB (256K x 8) FLASH 64-QFN Exposed Pad (9x9) 制造商:cypress semiconductor corp 系列:FM3 MB9A310A 包装:托盘 零件状态:有效 核心处理器:ARM? Cortex?-M3 核心尺寸:32-位 速度:40MHz 连接性:CSIO，I2C，LIN，UART/USART，USB 外设:DMA，LVD，POR，PWM，WDT I/O 数:51 程序存储容量:256KB（256K x 8） 程序存储器类型:闪存 EEPROM 容量:- RAM 容量:32K x 8 电压 - 电源（Vcc/Vdd）:2.7 V ~ 5.5 V 数据转换器:A/D 9x12b 振荡器类型:内部 工作温度:-40°C ~ 105°C（TA） 封装/外壳:64-VFQFN 裸露焊盘 供应商器件封装:64-QFN 裸露焊盘（9x9） 标准包装:260 |
| MB9AF314LPMC1-ESE1 | 制造商:FUJITSU 功能描述: |
| MB9AF314LPMC1-GE1 | 制造商:FUJITSU 功能描述: |
发布紧急采购，3分钟左右您将得到回复。