- 您现在的位置：买卖IC网 > PDF目录80366 > MB9AF314NBGL 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PBGA112 PDF资料下载
参数资料
| 型号： | MB9AF314NBGL |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PBGA112 |
| 封装： | 0.80 MM PITCH, PLASTIC, FBGA-112 |
| 文件页数： | 11/114页 |
| 文件大小： | 1357K |
| 代理商： | MB9AF314NBGL |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页
ATmega48PA/88PA/168PA [DATASHEET]
9223F–AVR–04/14
108
The general I/O port function is overridden by the output compare (OC1x) from the waveform generator if either of the
COM1x1:0 bits are set. However, the OC1x pin direction (input or output) is still controlled by the data direction register
(DDR) for the port pin. The data direction register bit for the OC1x pin (DDR_OC1x) must be set as output before the OC1x
value is visible on the pin. The port override function is generally independent of the waveform generation mode, but there
are some exceptions. Refer to Table 16-2 on page 116, Table 16-3 on page 117 and Table 16-4 on page 117 for details.
The design of the output compare pin logic allows initialization of the OC1x state before the output is enabled. Note that
some COM1x1:0 bit settings are reserved for certain modes of operation. See
The COM1x1:0 bits have no effect on the input capture unit.
16.8.1 Compare Output Mode and Waveform Generation
The waveform generator uses the COM1x1:0 bits differently in normal, CTC, and PWM modes. For all modes, setting the
COM1x1:0 = 0 tells the waveform generator that no action on the OC1x register is to be performed on the next compare
match. For compare output actions in the non-PWM modes refer to Table 16-2 on page 116. For fast PWM mode refer to
Table 16-3 on page 117, and for phase correct and phase and frequency correct PWM refer to Table 16-4 on page 117.
A change of the COM1x1:0 bits state will have effect at the first compare match after the bits are written. For non-PWM
modes, the action can be forced to have immediate effect by using the FOC1x strobe bits.
16.9
Modes of Operation
The mode of operation, i.e., the behavior of the Timer/Counter and the output compare pins, is defined by the combination of
the waveform generation mode (WGM13:0) and compare output mode (COM1x1:0) bits. The compare output mode bits do
not affect the counting sequence, while the waveform generation mode bits do. The COM1x1:0 bits control whether the
PWM output generated should be inverted or not (inverted or non-inverted PWM). For non-PWM modes the COM1x1:0 bits
control whether the output should be set, cleared or toggle at a compare match (See
For detailed timing information refer to Section 16.10 “Timer/Counter Timing Diagrams” on page 114.
16.9.1 Normal Mode
The simplest mode of operation is the normal mode (WGM13:0 = 0). In this mode the counting direction is always up
(incrementing), and no counter clear is performed. The counter simply overruns when it passes its maximum 16-bit value
(MAX = 0xFFFF) and then restarts from the BOTTOM (0x0000). In normal operation the Timer/Counter overflow flag (TOV1)
will be set in the same timer clock cycle as the TCNT1 becomes zero. The TOV1 flag in this case behaves like a 17th bit,
except that it is only set, not cleared. However, combined with the timer overflow interrupt that automatically clears the TOV1
flag, the timer resolution can be increased by software. There are no special cases to consider in the normal mode, a new
counter value can be written anytime.
The input capture unit is easy to use in normal mode. However, observe that the maximum interval between the external
events must not exceed the resolution of the counter. If the interval between events are too long, the timer overflow interrupt
or the prescaler must be used to extend the resolution for the capture unit.
The output compare units can be used to generate interrupts at some given time. Using the output compare to generate
waveforms in normal mode is not recommended, since this will occupy too much of the CPU time.
相关PDF资料 |
PDF描述 |
|---|---|
| MB9BF418SPMC | RISC MICROCONTROLLER, PQFP144 |
| M38802M1-XXXFS | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, CQCC64 |
| MAQ281CE | 16-BIT, MICROPROCESSOR, DMA64 |
| MAS281CS | 16-BIT, MICROPROCESSOR, DMA64 |
| M37730S2ASP | 16-BIT, 16 MHz, MICROCONTROLLER, PDIP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB9AF314NBGL-GE1 | 制造商:FUJITSU 功能描述: 制造商:FUJITSU 功能描述:MCU 32BIT CORTEX-M3 FM3 112BGA 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 112BGA 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 112BGA, Controller Family/Series:ARM Cortex-M3, Core 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 112BGA, Controller Family/Series:ARM Cortex-M3, Core Size:32bit, No. of I/O's:83, Supply Voltage Min:2.7V, Supply Voltage Max:5.5V, Digital IC Case Style:BGA, No. of Pins:112, Program Memory Size:256KB, , RoHS Compliant: Yes |
| MB9AF314NPMC-GE1 | 制造商:FUJITSU 功能描述: |
| MB9AF314NPMC-G-JNE1 | 制造商:FUJITSU 功能描述: 制造商:FUJITSU 功能描述:MCU 32BIT CORTEX-M3 FM3 100LQFP 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 100LQFP, Controller Family/Series:ARM Cortex-M3, Cor |
| MB9AF316MAPMC-G-JNE2 | 制造商:Fujitsu 功能描述:Bulk |
| MB9AF316MPMC-G-JNE1 | 制造商:FUJITSU 功能描述:MCU 32BIT CORTEX-M3 FM3 80LQFP 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 80LQFP, Controller Family/Series:ARM Cortex-M3, Core |
发布紧急采购，3分钟左右您将得到回复。