参数资料
型号: MB9AF314NBGL
元件分类: 微控制器/微处理器
英文描述: 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PBGA112
封装: 0.80 MM PITCH, PLASTIC, FBGA-112
文件页数: 51/114页
文件大小: 1357K
代理商: MB9AF314NBGL
41
ATmega48PA/88PA/168PA [DATASHEET]
9223F–AVR–04/14
11.
System Control and Reset
11.1
Resetting the AVR
During reset, all I/O registers are set to their initial values, and the program starts execution from the reset vector. For Atmel
ATmega168PA the instruction placed at the reset vector must be a JMP – absolute jump – instruction to the reset handling
routine. For the Atmel ATmega48PA and Atmel ATmega88PA, the instruction placed at the reset vector must be an RJMP –
relative jump – instruction to the reset handling routine. If the program never enables an interrupt source, the interrupt
vectors are not used, and regular program code can be placed at these locations. This is also the case if the reset vector is
in the application section while the interrupt vectors are in the boot section or vice versa (Atmel ATmega88PA/168PA only).
The circuit diagram in Figure 11-1 on page 42 shows the reset logic. Table 29-5 on page 272 defines the electrical
parameters of the reset circuitry.
The I/O ports of the AVR are immediately reset to their initial state when a reset source goes active. This does not require
any clock source to be running.
After all reset sources have gone inactive, a delay counter is invoked, stretching the internal reset. This allows the power to
reach a stable level before normal operation starts. The time-out period of the delay counter is defined by the user through
the SUT and CKSEL fuses. The different selections for the delay period are presented in
11.2
Reset Sources
The Atmel ATmega48PA/88PA/168PA has four sources of reset:
Power-on reset. The MCU is reset when the supply voltage is below the power-on reset threshold (VPOT).
External reset. The MCU is reset when a low level is present on the RESET pin for longer than the minimum pulse
length.
Watchdog system reset. The MCU is reset when the watchdog timer period expires and the watchdog system reset
mode is enabled.
Brown-out reset. The MCU is reset when the supply voltage VCC is below the brown-out reset threshold (VBOT) and the
brown-out detector is enabled.
相关PDF资料
PDF描述
MB9BF418SPMC RISC MICROCONTROLLER, PQFP144
M38802M1-XXXFS 8-BIT, MROM, 8 MHz, MICROCONTROLLER, CQCC64
MAQ281CE 16-BIT, MICROPROCESSOR, DMA64
MAS281CS 16-BIT, MICROPROCESSOR, DMA64
M37730S2ASP 16-BIT, 16 MHz, MICROCONTROLLER, PDIP64
相关代理商/技术参数
参数描述
MB9AF314NBGL-GE1 制造商:FUJITSU 功能描述: 制造商:FUJITSU 功能描述:MCU 32BIT CORTEX-M3 FM3 112BGA 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 112BGA 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 112BGA, Controller Family/Series:ARM Cortex-M3, Core 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 112BGA, Controller Family/Series:ARM Cortex-M3, Core Size:32bit, No. of I/O's:83, Supply Voltage Min:2.7V, Supply Voltage Max:5.5V, Digital IC Case Style:BGA, No. of Pins:112, Program Memory Size:256KB, , RoHS Compliant: Yes
MB9AF314NPMC-GE1 制造商:FUJITSU 功能描述:
MB9AF314NPMC-G-JNE1 制造商:FUJITSU 功能描述: 制造商:FUJITSU 功能描述:MCU 32BIT CORTEX-M3 FM3 100LQFP 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 100LQFP, Controller Family/Series:ARM Cortex-M3, Cor
MB9AF316MAPMC-G-JNE2 制造商:Fujitsu 功能描述:Bulk
MB9AF316MPMC-G-JNE1 制造商:FUJITSU 功能描述:MCU 32BIT CORTEX-M3 FM3 80LQFP 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 80LQFP, Controller Family/Series:ARM Cortex-M3, Core