参数资料
型号: MBM29LV160BE12PBT-E1
厂商: SPANSION LLC
元件分类: PROM
英文描述: 2M X 8 FLASH 3V PROM, 120 ns, PBGA48
封装: PLASTIC, FBGA-48
文件页数: 18/59页
文件大小: 759K
代理商: MBM29LV160BE12PBT-E1
MBM29LV160TE/BE-70/90/12
25
RESET
Hardware Reset Pin
The MBM29LV160TE/BE device may be reset by driving the RESET pin to VIL. The RESET pin has a pulse
requirement and has to be kept low (VIL) for at least “tRP” in order to properly reset the internal state machine.
Any operation in the process of being executed will be terminated and the internal state machine will be reset
to the read mode “tREADY” after the RESET pin is driven low. Furthermore, once the RESET pin goes high, the
device requires an additional “tRH” before it allows read access. When the RESET pin is low, the device will be
in the standby mode for the duration of the pulse and all the data output pins will be tri-stated. If a hardware
reset occurs during a program or erase operation, the data at that particular location will be corrupted. Please
note that the RY/BY output signal should be ignored during the RESET pulse. Refer to Figure 13 for the timing
diagram. Refer to Temporary Sector Unprotection for additional functionality.
If hardware reset occurs during Embedded Erase Algorithm, there is a possibility that the erasing sector(s) will
need to be erased again before they can be programmed.
Byte/Word Configuration
The BYTE pin selects the byte (8-bit) mode or word (16-bit) mode for the MBM29LV160TE/BE device. When
this pin is driven high, the device operates in the word (16-bit) mode. The data is read and programmed at DQ0
to DQ15. When this pin is driven low, the device operates in byte (8-bit) mode. Under this mode, DQ15/A-1 pin
becomes the lowest address bit and DQ8 to DQ14 bits are tri-stated. However, the command bus cycle is always
an 8-bit operation and hence commands are written at DQ0 to DQ7 and DQ8 to DQ15 bits are ignored. Refer to
Figures 14, 15 and 16 for the timing diagram.
Data Protection
The MBM29LV160TE/BE is designed to offer protection against accidental erasure or programming caused by
spurious system level signals that may exist during power transitions. During power up the device automatically
resets the internal state machine to the Read mode. Also, with its control register architecture, alteration of the
memory contents only occurs after successful completion of specific multi-bus cycle command sequence.
The device also incorporates several features to prevent inadvertent write cycles resulting form VCC power-up
and power-down transitions or system noise.
Low VCC Write Inhibit
To avoid initiation of a write cycle during VCC power-up and power-down, a write cycle is locked out for VCC less
than VLKO (min.). If VCC < VLKO, the command register is disabled and all internal program/erase circuits are
disabled. Under this condition, the device will reset to the read mode. Subsequent writes will be ignored until
the VCC level is greater than VLKO. It is the users responsibility to ensure that the control pins are logically correct
to prevent unintentional writes when VCC is above VLKO (min.).
If the Embedded Erase Algorithm is interrupted, there is possibility that the erasing sector(s) will need to be
erased again prior to programming.
Write Pulse “Glitch” Protection
Noise pulses of less than 5 ns (typical) on OE, CE, or WE will not change the command registers.
Logical Inhibit
Writing is inhibited by holding any one of OE = VIL, CE = VIH, or WE = VIH. To initiate a write, CE and WE must
be a logical zero while OE is a logical one.
Power-up Write Inhibit
Power-up of the devices with WE = CE = VIL and OE = VIH will not accept commands on the rising edge of WE.
The internal state machine is automatically reset to read mode on power-up.
相关PDF资料
PDF描述
MBM29LV200B-10PFTR 256K X 8 FLASH 3V PROM, 100 ns, PDSO48
MBM29LV800BE70TN 512K X 16 FLASH 3V PROM, 70 ns, PDSO48
MBPL1319B-1R2-KS 1 ELEMENT, 1.2 uH, GENERAL PURPOSE INDUCTOR
MBPL1319B-R30-KS 1 ELEMENT, 0.3 uH, GENERAL PURPOSE INDUCTOR
MBPL1319B-R90-KS 1 ELEMENT, 0.9 uH, GENERAL PURPOSE INDUCTOR
相关代理商/技术参数
参数描述
MBM29LV160BE12PCV 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT
MBM29LV160BE12TN 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT
MBM29LV160BE12TR 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT
MBM29LV160BE-70 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT
MBM29LV160BE70PBT 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT