- 您现在的位置：买卖IC网 > PDF目录296481 > MBM29LV160BE12PBT-E1 (SPANSION LLC) 2M X 8 FLASH 3V PROM, 120 ns, PBGA48 PDF资料下载
参数资料
| 型号： | MBM29LV160BE12PBT-E1 |
| 厂商： | SPANSION LLC |
| 元件分类： | PROM |
| 英文描述： | 2M X 8 FLASH 3V PROM, 120 ns, PBGA48 |
| 封装： | PLASTIC, FBGA-48 |
| 文件页数： | 3/59页 |
| 文件大小： | 759K |
| 代理商： | MBM29LV160BE12PBT-E1 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页
MBM29LV160TE/BE-70/90/12
11
s FUNCTIONAL DESCRIPTION
Read Mode
The MBM29LV160TE/BE has two control functions which must be satisfied in order to obtain data at the outputs.
CE is the power control and should be used for a device selection. OE is the output control and should be used
to gate data to the output pins if a device is selected.
Address access time (tACC) is equal to the delay from stable addresses to valid output data. The chip enable
access time (tCE) is the delay from stable addresses and stable CE to valid data at the output pins. The output
enable access time is the delay from the falling edge of OE to valid data at the output pins. (Assuming the
addresses have been stable for at least tACC - tOE time.) When reading out a data without changing addresses
after power-up, it is necessary to input hardware reset or to change CE pin from “H” or “L”.
Standby Mode
There are two ways to implement the standby mode on the MBM29LV160TE/BE devices. One is by using both
the CE and RESET pins; the other via the RESET pin only.
When using both pins, a CMOS standby mode is achieved with CE and RESET inputs both held at VCC ±0.3 V.
Under this condition the current consumed is less than 5
A max. During Embedded Algorithm operation, VCC
Active current (ICC2) is required even CE = “H”. The device can be read with standard access time (tCE) from
either of these standby modes.
When using the RESET pin only, a CMOS standby mode is achieved with the RESET input held at VSS ±0.3 V
(CE = “H” or “L”). Under this condition the current consumed is less than 5
A max. Once the RESET pin is
taken high, the device requires tRH of wake up time before outputs are valid for read access.
In the standby mode, the outputs are in the high-impedance state, independent of the OE input.
Automatic Sleep Mode
There is a function called automatic sleep mode to restrain power consumption during read-out of
MBM29LV160TE/BE data. This mode can be used effectively with an application requesting low power
consumption such as handy terminals.
To activate this mode, MBM29LV160TE/BE automatically switches itself to low power mode when addresses
remain stable for 150 ns. It is not necessary to control CE, WE, and OE in this mode. During such mode, the
current consumed is typically 1
A (CMOS Level).
Standard address access timings provide new data when addresses are changed. While in sleep mode, output
data is latched and always available to the system.
Output Disable
If the OE input is at a logic high level (VIH), output from the device is disabled. This will cause the output pins to
be in a high-impedance state.
Autoselect
The Autoselect mode allows the reading out of a binary code from the device and will identify its manufacturer
and type. The intent is to allow programming equipment to automatically match the device to be programmed
with its corresponding programming algorithm. The Autoselect command may also be used to check the status
of write-protected sectors. (See Tables 4.1 and 4.2.) This mode is functional over the entire temperature range
of the device.
To activate this mode, the programming equipment must force VID (11.5 V to 12.5 V) on address pin A9. Two
identifier bytes may then be sequenced from the devices outputs by toggling address A0 from VIL to VIH. All
addresses are DON’T CARES except A0, A1, and A6 (A-1). (See Table 2 or Table 3.)
相关PDF资料 |
PDF描述 |
|---|---|
| MBM29LV200B-10PFTR | 256K X 8 FLASH 3V PROM, 100 ns, PDSO48 |
| MBM29LV800BE70TN | 512K X 16 FLASH 3V PROM, 70 ns, PDSO48 |
| MBPL1319B-1R2-KS | 1 ELEMENT, 1.2 uH, GENERAL PURPOSE INDUCTOR |
| MBPL1319B-R30-KS | 1 ELEMENT, 0.3 uH, GENERAL PURPOSE INDUCTOR |
| MBPL1319B-R90-KS | 1 ELEMENT, 0.9 uH, GENERAL PURPOSE INDUCTOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MBM29LV160BE12PCV | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT |
| MBM29LV160BE12TN | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT |
| MBM29LV160BE12TR | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT |
| MBM29LV160BE-70 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT |
| MBM29LV160BE70PBT | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT |
发布紧急采购，3分钟左右您将得到回复。