- 您现在的位置：买卖IC网 > PDF目录16878 > MC10XS3412DPNA (Freescale Semiconductor)IC SWITCH HIGH SIDE QUAD 24QFN PDF资料下载
参数资料
| 型号： | MC10XS3412DPNA |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 32/55页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH HIGH SIDE QUAD 24QFN |
| 标准包装： | 168 |
| 类型： | 高端开关 |
| 输出数： | 4 |
| Rds（开）： | 2 x 10 毫欧，2 x 12 毫欧 |
| 内部开关： | 是 |
| 电流限制： | 5A |
| 输入电压： | 4 V ~ 28 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-PowerQFN |
| 供应商设备封装： | 24-PQFN（12x12） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页
FUNCTIONAL DEVICE OPERATION
PROTECTION AND DIAGNOSTIC FEATURES
AUTORETRY
The autoretry circuitry is used to reactivate the output(s)
automatically in case of overcurrent or overtemperature or
undervoltage failure conditions to provide a high availability
of the load.
Autoretry feature is available in Fault mode. It is activated
in case of internal retry signal is set to logic [1]:
retry[x] = OC[x] or OT[x] or UV.
The feature retries to switch-on the output(s) after one
autoretry period (t AUTO ) with a limitation in term of number of
occurrence (16 for each output). The counter of retry
occurrences is reset in cases of mode transitions (refer to
bit toggling. At each autoretry, the overcurrent detection will
be set to default values in order to sustain the inrush current.
The Figure 12 describes the autoretry state machine.
DIAGNOSTIC
Output Shorted to VPWR Fault
The 10XS3412 incorporates output shorted to VPWR
detection circuitry in OFF state. Output shorted to VPWR fault
is detected if output voltage is higher than V OSD(THRES) and
reported as a fault condition when the output is disabled
(OFF). The output shorted to VPWR fault is latched into the
status register after the internal gate voltage is pulled low
enough to turn OFF the output. The OS[0:3] and
OL_OFF[0:3] fault bits are set in the status register and FS
pin reports in real time the fault. If the output shorted to
VPWR fault is removed, the status register will be cleared
after reading the register.
The open output shorted to VPWR protection can be
disabled through SPI (OS_DIS[0:3] bit).
Open-Load Faults
The 10XS3412 incorporates three dedicated open-load
detection circuitries on the output to detect in OFF and in ON
state.
Open-load Detection In Off State
The OFF output open-load fault is detected when the
output voltage is higher than V OLD(THRES) pulled up with
internal current source ( I OLD(OFF) ) and reported as a fault
condition when the output is disabled (OFF). The OFF Output
open-load fault is latched into the status register or when the
internal gate voltage is pulled low enough to turn OFF the
output. The OL_OFF[0:3] fault bit is set in the status register.
If the open load fault is removed (FS output pin goes to high),
the status register will be cleared after reading the register.
The OFF output open-load protection can be disabled
through SPI (OLOFF_DIS[0:3] bit).
Open-load Detection In On State
The ON output open-load current thresholds can be
chosen by SPI to detect a standard bulbs or LEDs
(OLLED[0:3] bit set to logic [1]). In the cases where load
current drops below the defined current threshold, th e OLON
bit is set to logic [1], and the output stays ON and FS will not
be disturbed.
Open-load Detection In On State For Led
Open load for LEDs only (OLLED[0:3] set to logic [1]) is
detected periodically each t OLLED (fully-on, D[6:0]=7F) . To
detect OLLED in the fully-on state, the output must be ON at
least t OLLED.
To delatch the diagnosis, the condition should be removed
and SPI read operation is needed (OL_ON[0:3] bit). The ON
output open-load protection can be disabled through SPI
(OLON_DIS[0:3] bit).
Analog Current Recopy and Temperature Feedbacks
The CSNS pin is an analog output reporting a current
proportional to the designed output current or a voltage
proportional to the temperature of the GND flag (pin #14).
The routing is SPI programmable (TEMP_en, CSNS_en,
CSNS_s[1,0] and CSNS_ratio_s bits).
In case the current recopy is active, the CSNS output
delivers current only during ON time of the output switch
without overshoot. The maximum current is 2.0 mA typical.
The typical value of external CSNS resistor connected to the
ground is 4.7 k ? .
The current recopy is not active in Fail-safe mode.
Temperature Prewarning Detection
In Normal mode, the 10XS3412 provides a temperature
prewarning reported via SPI in case of the temperature of the
GND flag is higher than T OTWAR . This diagnosis (OTW bit set
to [1]) is latched in the SPI DIAGR0 register. To delatch, a
read SPI command is needed.
ACTIVE CLAMP ON VPWR
The device provides an active gate clamp circuit in order
to limit the maximum transient VPWR voltage at
VPWR (CLAMP) . In case of an overload on an output, the
corresponding output is turned off, which leads to a high-
voltage at VPWR with an inductive VPWR line. When VPWR
voltage exceeds VPWR (CLAMP) threshold, the turn-off on the
corresponding output is deactivated and all HS[0:3] outputs
are switched ON automatically to demagnetize the inductive
Battery line.
For a long battery line between the battery and the device
(> 20 meters), the smart high side switch output may exceed
the energy capability in case of a short-circuit. It is
recommended to implement a voltage transient suppressor
to drain the battery line energy.
REVERSE BATTERY ON VPWR
The output survives the application of reverse voltage as
low as -18 V. Under these conditions, the ON resistance of
the output is 2 times higher than typical ohmic value in
10XS3412
Analog Integrated Circuit Device Data ?
32
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J6B-EY | CONVERTER MOD DC/DC 95V 50W |
| MAX6065AEUR+T | IC VREF SERIES PREC 5V SOT-23-3 |
| FFSD-10-S-20.00-01-N | CABLE ASSY 2X10 IDC |
| GCC15DRTH-S13 | CONN EDGECARD 30POS .100 EXTEND |
| 222D253-3/86-0 | BOOT MOLDED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC10XS3412DPNAR2 | 功能描述:电源开关 IC - 配电 Eswitch Gen3 1012 RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC10XS3412JHFK | 制造商:Freescale Semiconductor 功能描述:SWITCH, QUAD, HS; Power Load Switch Type:Quad High Side; Input Voltage:5.5V; No. of Pins:24; Thermal Protection:Yes; On / Enable Input Polarity:Active Low; No. of Outputs:4; Operating Temperature Min:-40C; Operating Temperature ;RoHS Compliant: Yes |
| MC10XS3412JHFKR2 | 功能描述:电源开关 IC - 配电 RoHS:否 制造商:Freescale Semiconductor 输出端数量: 开启电阻（最大值）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压: 电源电流（最大值）: 最大工作温度: 安装风格: 封装 / 箱体: |
| MC10XS3412KHFKR2 | 功能描述:电源开关 IC - 配电 RoHS:否 制造商:Freescale Semiconductor 输出端数量: 开启电阻（最大值）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压: 电源电流（最大值）: 最大工作温度: 安装风格: 封装 / 箱体: |
| MC10XS3425EK | 功能描述:电源开关 IC - 配电 SPQL1025 RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
发布紧急采购，3分钟左右您将得到回复。