- 您现在的位置：买卖IC网 > PDF目录1851 > MC33874BPNAR2 (Freescale Semiconductor)IC SW QUAD HI SIDE 35MOHM 24PQFN PDF资料下载
参数资料
| 型号： | MC33874BPNAR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 19/38页 |
| 文件大小： | 0K |
| 描述： | IC SW QUAD HI SIDE 35MOHM 24PQFN |
| 标准包装： | 1,200 |
| 类型： | 高端 |
| 输入类型： | SPI |
| 输出数： | 4 |
| 导通状态电阻： | 35 毫欧 |
| 电源电压： | 6 V ~ 27 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-PowerQFN |
| 供应商设备封装： | 24-PQFN（12x12） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
FUNCTIONAL DEVICE OPERATION
PROTECTION AND DIAGNOSTIC FEATURES
resistance limiting the internal clamp current according to the
specification.
The Watchdog timeout is a multiple of an internal oscillator
and is specified in the Table 15 , page 24 . As long as the WD
bit (D15) of an incoming SPI message is toggled within the
minimum watchdog timeout period (WDTO), based on the
programmed value of the WDR, the device will operate
normally. If an internal watchdog timeout occurs before the
WD bit, the device will revert to a Fail-safe mode until the
device is reinitialized.
During the Fail-safe Mode, the outputs will be ON or OFF
depending upon the resistor RFS connected to the FSI pin,
regardless of the state of the various direct inputs and modes
Table 6. Output State During Fail-safe Mode
Table 5 summarizes the various methods for resetting the
device from the latched Fail-safe Mode.
If the FSI pin is tied to GND, the Watchdog fail-safe
operation is disabled.
LOSS OF V DD
If the external 5.0 V supply is not within specification, or
even disconnected, all register content is reset. The outputs
can still be driven by the direct inputs IN0 : IN3. The 33874
uses the battery input to power the output MOSFET-related
current sense circuitry and any other internal logic providing
fail-safe device operation with no V DD supplied. In this state,
the watchdog, under-voltage, over-voltage, over-temperature
(latched) and over-current circuitry are fully operational with
default values.
RFS (k Ω )
0 (shorted to ground)
6.0
High Side State
Fail-safe Mode Disabled
All HS OFF
FAULT MODE
This 33874 indicates the faults below as they occur by
driving the FS pin to logic [0]:
15
30 (open)
HS0 ON
HS1 : HS3 OFF
HS0 and HS2 ON
HS1 and HS3 OFF
?
?
?
?
Over-temperature fault
Over-voltage and under-voltage fault
Open load fault
Over-current fault (high and low)
In the Fail-safe Mode, the SPI register content is retained
except for over-current high and low detection levels, timing
and latched over-temperature which are reset to their default
value (SOCL, SOCH, and OCTL and OT_latch_[0:3] bits).
Then the watchdog, over-voltage, over-temperature, and
over-current circuitry (with default value) are fully operational.
The Fail-safe Mode can be detected by monitoring the
WDTO bit D2 of the WD register. This bit is logic [1] when the
device is in Fail-safe Mode. The device can be brought out of
the Fail-safe Mode by transitioning the WAKE and RST pins
The FS pin will automatically return to logic [1] when the
fault condition is removed, except for overcurrent,
overtemperature (in case of latching configuration) and in
some cases of undervoltage.
The FS pin reports all faults. For latched faults, this pin is
reset by a new Switch ON command (via the SPI or direct
input IN).
Fault information is retained in the fault register and is
available (and reset) via the SO pin during the first valid SPI
communication (refer to Table 17 , page 26 ).
from logic [1] to logic [0] or forcing the FSI pin to logic [0].
PROTECTION AND DIAGNOSTIC FEATURES
OVER-TEMPERATURE FAULT (LATCHING OR
NON-LATCHING)
The 33874 incorporates over-temperature detection and
shutdown circuitry for each output structure.
The over-temperature is latched per default and can be
unlatched through SPI with OT_latch_[0:3] bits.
An over-temperature fault condition results in turning OFF
the corresponding output. To remove the fault and be able to
turn ON again the outputs, the failure must be removed and:
? in Normal Mode: the corresponding output must be
commanded OFF and ON again in case of over-
temperature latched (OT_latch bit = 0).
? in Normal Mode: the corresponding output turns ON
automatically if the temperature is below T SD -T SD(HYS) in
case of unlatched over-temperature (OT_latch bit = 1).
? in Fail-safe Mode: the FSI input must be grounded and
then set to its nominal voltage to switch ON the outputs.
The over-temperature fault (one for each output) is
reported by SPI. If the over-temperature is latched, the SPI
reports OTF_s = [1] and OCLF_s = [1]. In case of non-
latched, OTF_s = [1] only is reported.
The fault bits will be cleared in the status register after either
a valid SPI read command or a power on reset of the device.
OVERCURRENT FAULT (LATCHING)
The 33874 has eight programmable over-current low
detection levels (I OCL ) and two programmable over-current
high detection levels (I OCH ) for maximum device protection.
The two selectable, simultaneously active over-current
33874
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
相关PDF资料 |
PDF描述 |
|---|---|
| MC33910G5ACR2 | IC SYSTEM BASIS CHIP 32LQFP |
| MC33911G5ACR2 | IC SYSTEM BASIS CHIP 32LQFP |
| MC33912G5ACR2 | IC SYSTEM BASIS CHIP 32LQFP |
| MC33926PNBR2 | IC H-BRIDGE THROTTLE CTRL 32-QFN |
| MC33931VWR2 | IC H-BRIDGE THROTTLE CTRL 44HSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33879APEK | 功能描述:电源开关 IC - 配电 CONFIG OCTAL SERIAL SW RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC33879APEKR2 | 功能描述:电源开关 IC - 配电 CONFIG OCTAL SERIAL SW RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC33879EK | 功能描述:电源开关 IC - 配电 CONFIG OCTAL SERIAL SW W RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC33879EKR2 | 功能描述:电源开关 IC - 配电 CONFIG OCTAL SERIAL SW W RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC33879TEK | 功能描述:电源开关 IC - 配电 CONFIG OCTAL SER SWITCH RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
发布紧急采购，3分钟左右您将得到回复。