- 您现在的位置：买卖IC网 > PDF目录16634 > MC33910G5AC (Freescale Semiconductor)IC SYSTEM BASIS CHIP 32LQFP PDF资料下载
参数资料
| 型号： | MC33910G5AC |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 67/90页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM BASIS CHIP 32LQFP |
| 标准包装： | 250 |
| 应用： | 系统基础芯片 |
| 电流 - 电源： | 4.5mA |
| 电源电压： | 5.5 V ~ 27 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-LQFP |
| 供应商设备封装： | 32-LQFP（7x7） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页当前第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页
MC33910BAC / MC34910BAC
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
INTERRUPT (IRQ)
The IRQ pin is a digital output used to signal events or
faults to the MCU while in Normal and Normal Request mode
or to signal a wake-up from Stop mode. This active low output
will transition to high, only after the interrupt is acknowledged
by a SPI read of the respective status bits.
WATCHDOG CONFIGURATION (WDCONF)
The WDCONF pin is the configuration pin for the internal
watchdog. A resistor can be connected to this pin to configure
the window watchdog period. When connected directly to
ground, the watchdog will be disabled. When this pin is left
open, the watchdog period is fixed to its lower precision
internal default value (150 ms typical).
GROUND CONNECTION (AGND, PGND, LGND)
The AGND, PGND and LGND pins are the Analog and
Power ground pins.
The AGND pin is the ground reference of the voltage
regulator.
The PGND and LGND pins are used for high current load
return as in the LIN interface pin.
Note: PGND, AGND and LGND pins must be connected
together.
DIGITAL/ANALOG (L1)
The L1 pin is a multi purpose input. It can be used as a
digital input, which can be sampled by reading the SPI and
used for wake-up when 33910 is in Low Power mode or used
as analog inputs for the analog multiplexer. When used to
sense voltage outside the module, a 33kohm series resistor
must be used on each input.
When used as a wake-up input L1 can be configured to
operate in Cyclic-Sense mode. In this mode, one of the high
side switches is configured to be periodically turned on and
sample the wake-up input. If a state change is detected
between two cycles a wake-up is initiated. The 33910 can
also wake-up from Stop or Sleep by a simple state change on
L1.
When used as analog input, the voltage present on the L1
pins is scaled down by an selectable internal voltage divider
and can be routed to the ADOUT0 output through the analog
multiplexer.
Note: If L1 input is selected in the analog multiplexer, it will
be disabled as digital input and remains disabled in low
Power mode. No wake-up feature is available in that
condition.
When the L1 input is not selected in the analog
HIGH SIDE OUTPUTS (HS1 AND HS2)
These high side switches are able to drive loads such as
relays or lamps. Their structure is connected to the VS2
supply pin. The pins are short-circuit protected and also
protected against overheating.
HS1and HS2 are controlled by SPI and can respond to a
signal applied to the PWMIN input pin.
The HS1 and HS2 outputs can also be used during Low
Power mode for the cyclic-sense of the wake input.
POWER SUPPLY (VS1 AND VS2)
Those are the battery level voltage supply pins. In an
application, VS1 and VS2 pins must be protected against
reverse battery connection and negative transient voltages,
with external components. These pins sustain standard
automotive voltage conditions such as load dump at 40 V.
The high side switches (HS1 and HS2) are supplied by the
VS2 pin, all other internal blocks are supplied by VS1 pin.
VOLTAGE SENSE PIN (VSENSE)
This input can be connected directly to the battery line. It
is protected against battery reverse connection. The voltage
present in this input is scaled down by an internal voltage
divider, and can be routed to the ADOUT0 output pin and
used by the MCU to read the battery voltage.
The ESD structure on this pin allows for excursion up to
+40 V, and down to -27 V, allowing this pin to be connected
directly to the battery line. It is strongly recommended to
connect a 10kohm resistor in series with this pin for protection
purposes.
HALL SENSOR SWITCHABLE SUPPLY PIN (HVDD)
This pin provides a switchable supply for external hall
sensors. While in Normal mode, this current limited output
can be controlled through the SPI.
The HVDD pin needs to be connected to an external
capacitor to stabilize the regulated output voltage.
+5V MAIN REGULATOR OUTPUT (VDD)
An external capacitor has to be placed on the VDD pin to
stabilize the regulated output voltage. The VDD pin is
intended to supply a microcontroller. The pin is current limited
against shorts to GND and over-temperature protected.
During Stop mode the voltage regulator does not operate
with its full drive capabilities and the output current is limited.
During Sleep mode the regulator output is completely shut
down.
multiplexer, the voltage divider is disconnected from that
input.
33910
Analog Integrated Circuit Device Data
67
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| 21020-0057 | CABLE FLAT FLEX 4" .50MM 6 POS |
| VE-B5W-EW | CONVERTER MOD DC/DC 5.5V 100W |
| A4973SB-T | IC PWM MOTOR DVR FULL 16DIP |
| MC33910BACR2 | IC SYSTEM BASIS CHIP 32LQFP |
| VE-B5V-EW | CONVERTER MOD DC/DC 5.8V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33910G5ACR2 | 功能描述:LIN 收发器 SBC LIN 2.5G Low end RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MC33911BAC | 功能描述:LIN 收发器 SBC LIN2G MEDIUM END RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MC33911BACR2 | 功能描述:LIN 收发器 SBC LIN2G MEDIUM END RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MC33911G5AC | 功能描述:LIN 收发器 SBC LIN 2.5G Medium end RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MC33911G5ACR2 | 功能描述:LIN 收发器 SBC LIN 2.5G Medium end RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
发布紧急采购，3分钟左右您将得到回复。