参数资料
| 型号： | MC34703PNB |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 27/46页 |
| 文件大小： | 0K |
| 描述： | IC POWER SUPPLY QUICC 33-QFN |
| 标准包装： | 1 |
| 应用： | 电源 |
| 电流 - 电源： | 60mA |
| 电源电压： | 2.8 V ~ 13.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 33-PowerQFN |
| 供应商设备封装： | 33-PQFN（10x10） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
Communication Stop
Only the master can terminate the data transfer by issuing
a STOP condition. The slave waits for this condition to
resume its initial state waiting for the next START condition
(see Figure 26 ).
Data Transfer Example
The master device controlling the I 2 C bus will always start
addressing a 34703 slave IC in writing mode (R/W = 0) in
should be included before the STOP condition (P); for
instance, 001 10010 to set switcher in its second setting
(switcher output voltage = +2% above its nominal value).
S A6 A5 A4 A3 A2 A1 A0 0 Ack
order to be able to write a Command Byte just after the
address acknowledge. I 2 C bus protocol defines this
START
Slave Address
Write
circumstance as a master-transmitter and slave-receiver
configuration.
Eventually this Command Byte can again define a Write
0
0
1
0
0
0
0
0 Ack
operation (e.g., Voltage Margining, see Figure 26 ), and the
master will keep the data transfer direction.
Figure 26 illustrates a communication beginning with the
slave address, the first command for voltage margining, and
a third byte containing the address field 001 and the value
field 00101 corresponding with the LDO fifth setting (LDO
output voltage = +5% above its nominal value). If a
simultaneous setting for switcher is needed, a fourth byte
First Command for Voltage Margining
0 0 1 0 0 1 0 1 Ack P
Address Field Value Field = LDO
5 th Setting
Figure 26. Complete Data Transfer Example
STOP
34703
Analog Integrated Circuit Device Data
Freescale Semiconductor
27
相关PDF资料 |
PDF描述 |
|---|---|
| MC34704AEP | IC POWER MANAGEMENT 56-QFN |
| MC34708VM | IC POWER MANAGEMENT 206MAPBGA |
| MC34710EWR2 | IC PWR SUPPLY ADJ DUAL SW 32SOIC |
| MC34712EPR2 | IC CONVERTER DDR 24QFN |
| MC34713EPR2 | IC CONVERTER DDR 24QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC34704AEP | 功能描述:开关变换器、稳压器与控制器 DSC8 PASS.1.3 RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MC34704AEPR2 | 功能描述:开关变换器、稳压器与控制器 DSC8 PASS1.3 TAPE RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MC34704BEP | 功能描述:开关变换器、稳压器与控制器 5CH DC-DC PWR MANGMNET I RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MC34704BEPR2 | 功能描述:开关变换器、稳压器与控制器 5CH DC-DC PWR MANGMNET RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MC34705 | 制造商:SPC Multicomp 功能描述:HEADER VERTICAL 12WAY 制造商:SPC Multicomp 功能描述:HEADER, VERTICAL, 12WAY |
发布紧急采购，3分钟左右您将得到回复。