- 您现在的位置：买卖IC网 > PDF目录69028 > MC68HC05G1B (MOTOROLA INC) 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP56 PDF资料下载
参数资料
| 型号： | MC68HC05G1B |
| 厂商： | MOTOROLA INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP56 |
| 封装： | SDIP-56 |
| 文件页数： | 58/124页 |
| 文件大小： | 732K |
| 代理商： | MC68HC05G1B |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页当前第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页
MC68HC05G1
MOTOROLA
5-5
INTERRUPTS
5
5.2
Hardware Controlled Sequences
The following three functions are not strictly interrupts, however, they are tied very closely to the
interrupts. These functions are RESET, STOP, WAIT.
1) RESET
The RESET input pin causes the program to go to its starting
address. This address is specied by the contents of memory
locations $3FFE and $3FFF. The interrupt mask of the Condition
Code register is also set. Much of the MCU is congured to some
known state as described in Table 4-1.
2) STOP
If the user chooses to use an interrupted RTC, the STOP
instruction causes the oscillator to be turned off and the
processor “sleeps” until an external interrupt (IRQ, INT1 or INT2)
or RESET occurs. If non-interrupted RTC is used, only the
internal processor clock is turned off. See section 7 on Low
Power Modes.
3) WAIT
The WAIT instruction causes all processor clocks to stop, but
leaves the RTC, Timer, and SPI clocks running. This “rest” state
of the processor can be cleared by RESET, an external interrupt
(IRQ, INT1 or INT2), RTC, Timer or SPI interrupt. There are no
special wait vectors for these individual interrupts. See section 7
on Low Power Modes.
5.3
Software Interrupt (SWI)
The software interrupt is an executable instruction. The action of the SWI instruction is similar to
the hardware interrupts. The SWI is executed regardless of the state of the interrupt mask in the
Condition Code register. The service routine address is specied by the contents of memory
location $3FFC and $3FFD.
5.4
External Interrupts (IRQ, INT1 & INT2)
There are two types of external interrupt in the MC68HC05G1. They can be software congured
for negative-edge or level sensitive triggering.
IRQ
When the signal of the external interrupt pin, IRQ, satises the condition
selected by the IRQN bit in the Miscellaneous Control register (bits 5 of
address $27) then an external interrupt occurs. The actual processor interrupt
is generated only if the interrupt mask bit of the Condition Code register is
also cleared. When the interrupt is recognized, the current state of the
processor is pushed onto the stack and the interrupt mask bit in the Condition
TPG
37
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC705JB2DW | 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, PDSO20 |
| MC68HC705JB2P | 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, PDIP20 |
| MC68HC705JB4P | 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, PDIP28 |
| MC68HC705K1CDW | 8-BIT, OTPROM, 2 MHz, MICROCONTROLLER, PDSO16 |
| MC68HC705K1CP | 8-BIT, OTPROM, 2 MHz, MICROCONTROLLER, PDIP16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC68HC05J1 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:HCMOS MICROCONTROLLER UNIT |
| MC68HC05J1A | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC68HC05J1ACDW | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC68HC05J1ACP | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC68HC05J1ADW | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
发布紧急采购，3分钟左右您将得到回复。