参数资料
型号: MCHC705JJ7CPE
厂商: Freescale Semiconductor
文件页数: 25/164页
文件大小: 0K
描述: IC MCU 8BIT 224 BYTES RAM 20PDIP
标准包装: 18
系列: HC05
核心处理器: HC05
芯体尺寸: 8-位
速度: 2.1MHz
连通性: SIO
外围设备: POR,温度传感器,WDT
输入/输出数: 14
程序存储器容量: 6KB(6K x 8)
程序存储器类型: OTP
RAM 容量: 224 x 8
电压 - 电源 (Vcc/Vdd): 2.7 V ~ 5.5 V
数据转换器: A/D 4x12b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 20-DIP(0.300",7.62mm)
包装: 管件
EPROM/OTPROM
MC68HC705JJ7 MC68HC705JP7 Advance Information Data Sheet, Rev. 4.1
120
Freescale Semiconductor
ELAT — EPROM Bus Latch Bit
This read/write bit configures address and data buses for programming the EPROM array. EPROM
data cannot be read when ELAT is set. Clearing the ELAT bit also clears the EPGM bit. Reset clears
ELAT.
1 = Address and data buses configured for EPROM programming of the array. The address and
data buses are latched in the EPROM array when a subsequent write to the array is made. Data
in the EPROM array cannot be read.
0 = Address and data buses configured for normal operation
Whenever the ELAT bit is cleared, the EPGM bit is also cleared. Both the EPGM and the ELAT bit cannot
be set using the same write instruction. Any attempt to set both the ELAT and EPGM bit on the same write
instruction cycle will result in the ELAT bit being set and the EPGM bit being cleared. To program a byte
of EPROM, manipulate the EPROG register as follows:
1.
Set the ELAT bit in the EPROG register.
2.
Write the desired data to the desired EPROM address.
3.
Set the EPGM bit in the EPROG register for the specified programming time, tEPGM.
4.
Clear the ELAT and EPGM bits in the EPROG register.
13.2.2 Mask Option Register
The mask option register (MOR) shown in Figure 13-2 is an EPROM byte that controls eight mask options.
The MOR is unaffected by reset. The erased state of the MOR is $00. The options that can be
programmed by the MOR are:
1.
Port software programmable pulldown devices (enable or disable)
2.
Startup delay after stop (16 or 4064 cycles)
3.
Oscillator shunt resistor (2 M
or open)
4.
STOP instruction (enable or disable)
5.
Low-voltage reset (enable or disable)
6.
Port A external interrupt function (enable or disable)
7.
IRQ trigger sensitivity (edge-triggered only or both edge- and level-triggered)
8.
COP watchdog (enable or disable)
SWPDI — Software Pulldown Inhibit Bit
This EPROM bit inhibits software control of the port A and port B pulldown devices.
1 = Software pulldown inhibited
0 = Software pulldown enabled
Address:
$1FF1
Bit 7
6
5
4321
Bit 0
Read:
SWPDI
DELAY
OSCRES
SWAIT
LVREN
PIRQ
LEVEL
COPEN
Write:
Reset:
Unaffected by reset
Erased:
0
00000
Figure 13-2. Mask Option Register (MOR)
相关PDF资料
PDF描述
VI-B4L-IX-B1 CONVERTER MOD DC/DC 28V 75W
VI-B4K-IW-B1 CONVERTER MOD DC/DC 40V 100W
VI-B4J-IX-B1 CONVERTER MOD DC/DC 36V 75W
VI-B4J-IW-B1 CONVERTER MOD DC/DC 36V 100W
VI-B43-IX-B1 CONVERTER MOD DC/DC 24V 75W
相关代理商/技术参数
参数描述
MCHC705JP7CDWE 功能描述:8位微控制器 -MCU 8B MCU 224 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
MCHC705KJ1CDWE 功能描述:8位微控制器 -MCU 8 BIT MCU 64 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
MCHC705KJ1CDWE 制造商:Freescale Semiconductor 功能描述:8-Bit Microcontroller IC
MCHC705KJ1CPE 功能描述:IC MCU 8BIT 64 BYTES RAM 16PDIP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:HC05 标准包装:1 系列:87C 核心处理器:MCS 51 芯体尺寸:8-位 速度:16MHz 连通性:SIO 外围设备:- 输入/输出数:32 程序存储器容量:8KB(8K x 8) 程序存储器类型:OTP EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4 V ~ 6 V 数据转换器:- 振荡器型:外部 工作温度:0°C ~ 70°C 封装/外壳:44-DIP 包装:管件 其它名称:864285
MCHC711KS2CFNE3 功能描述:8位微控制器 -MCU 32K EPROM - SLO MODE RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT