- 您现在的位置：买卖IC网 > PDF目录45332 > MKI41T56S00TR (STMICROELECTRONICS) 0 TIMER(S), REAL TIME CLOCK, PDSO8 PDF资料下载
参数资料
| 型号： | MKI41T56S00TR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 时钟/数据恢复及定时提取 |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, PDSO8 |
| 封装： | 0.150 INCH, PLASTIC, SOP-8 |
| 文件页数： | 13/16页 |
| 文件大小： | 105K |
| 代理商： | MKI41T56S00TR |
MK41T56, MKI41T56
6/16
Table 9. Power Down/Up Mode AC Characteristics
(TA = 0 to 70 °C or –40 to 85°C)
Symbol
Parameter
Min
Max
Unit
tPD
SCL and SDA at VIH before Power Down
0ns
tFB
VPFD (min) to VSO VCC Fall Time
300
s
tRB
VSO to VPFD (min) VCC Rise Time
100
s
tREC
SCL and SDA at VIH after Power Up
200
s
Figure 6. Power Down/Up Mode AC Waveforms
AI00595
VCC
tFB
tREC
tPD
tRB
VPFD
VSO
DATA RETENTION TIME
SDA
SCL
IBAT
2-WIRE BUS CHARACTERISTICS
This bus is intended for communication between
different ICs. It consists of two lines: one bi-direc-
tional for data signals (SDA) and one for clock sig-
nals (SCL). Both the SDA and the SCL lines must
be connected to a positive supply voltage via a
pull-up resistor.
The following protocol has been defined:
– Data transfer may be initiated only when the bus
is not busy.
– During data transfer, the data line must remain
stable whenever the clock line is High.
– Changes in the data line while the clock line is
High will be interpreted as control signals.
Accordingly, the following bus conditions have
been defined:
Bus not busy. Both data and clock lines remain
High.
Start data transfer. A change in the state of the
data line, from High to Low, while the clock is High,
defines the START condition.
Stop data transfer. A change in the state of the
data line, from Low to High, while the clock is High,
defines the STOP condition.
Data valid. The state of the data line represents
valid data when after a start condition, the data line
is stable for the duration of the High period of the
clock signal. The data on the line may be changed
during the Low period of the clock signal. There is
one clock pulse per bit of data.
Each data transfer is initiated with a start condition
and terminated with a stop condition. The number
相关PDF资料 |
PDF描述 |
|---|---|
| ML2035IP | 1-BIT, DSP-NUM CONTROLLED OSCILLATOR, PDIP8 |
| ML54053 | IDE COMPATIBLE, FLASH MEMORY DRIVE CONTROLLER, PQFP120 |
| ML610Q346J-NNNTB | 8-BIT, FLASH, 4.2 MHz, RISC MICROCONTROLLER, PQFP64 |
| ML610Q409-NNNTBZ03A | RISC MICROCONTROLLER, PQFP100 |
| ML610Q408-NNNTBZ03A | RISC MICROCONTROLLER, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MKI50-06A7 | 功能描述:IGBT 模块 50 Amps 600V RoHS:否 制造商:Infineon Technologies 产品:IGBT Silicon Modules 配置:Dual 集电极—发射极最大电压 VCEO:600 V 集电极—射极饱和电压:1.95 V 在25 C的连续集电极电流:230 A 栅极—射极漏泄电流:400 nA 功率耗散:445 W 最大工作温度:+ 125 C 封装 / 箱体:34MM 封装: |
| MKI50-06A7T | 功能描述:分立半导体模块 50 Amps 600V RoHS:否 制造商:Infineon Technologies 产品:Thyristor Power Modules 类型:Phase Controls 安装风格:Screw 封装 / 箱体:DT61 封装: |
| MKI50-12E7 | 功能描述:分立半导体模块 IGBT (NPT3) 1200V 50A RoHS:否 制造商:Infineon Technologies 产品:Thyristor Power Modules 类型:Phase Controls 安装风格:Screw 封装 / 箱体:DT61 封装: |
| MKI50-12F7 | 功能描述:IGBT 模块 50 Amps 1200V RoHS:否 制造商:Infineon Technologies 产品:IGBT Silicon Modules 配置:Dual 集电极—发射极最大电压 VCEO:600 V 集电极—射极饱和电压:1.95 V 在25 C的连续集电极电流:230 A 栅极—射极漏泄电流:400 nA 功率耗散:445 W 最大工作温度:+ 125 C 封装 / 箱体:34MM 封装: |
| MKI65-06A7T | 功能描述:分立半导体模块 65 Amps 600V RoHS:否 制造商:Infineon Technologies 产品:Thyristor Power Modules 类型:Phase Controls 安装风格:Screw 封装 / 箱体:DT61 封装: |
发布紧急采购，3分钟左右您将得到回复。