- 您现在的位置：买卖IC网 > PDF目录189259 > NT5DS64M8BF-6KI (NANYA TECHNOLOGY CORP) DDR DRAM, PBGA60 PDF资料下载
参数资料
| 型号： | NT5DS64M8BF-6KI |
| 厂商： | NANYA TECHNOLOGY CORP |
| 元件分类： | DRAM |
| 英文描述： | DDR DRAM, PBGA60 |
| 封装： | 1 MM PITCH, WBGA-60 |
| 文件页数： | 11/79页 |
| 文件大小： | 6238K |
| 代理商： | NT5DS64M8BF-6KI |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页
NT5DS128M4BF
NT5DS128M4BT
NT5DS128M4BG
NT5DS128M4BS
NT5DS64M8BF
NT5DS64M8BT
NT5DS64M8BG
NT5DS64M8BS
NT5DS32M16BF
NT5DS32M16BT
NT5DS32M16BG
NT5DS32M16BS
512Mb DDR SDRAM
REV 1.3
11/2007
19
NANYA TECHNOLOGY CORP. All rights reserved.
NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice.
Auto Precharge
Auto Precharge is a feature which performs the same individual-bank precharge function described above, but without requiring
an explicit command. This is accomplished by using A10 to enable Auto Precharge in conjunction with a specific Read or Write
command. A precharge of the bank/row that is addressed with the Read or Write command is automatically performed upon
completion of the Read or Write burst. Auto Precharge is non-persistent in that it is either enabled or disabled for each individual
Read or Write command. Auto Precharge ensures that the precharge is initiated at the earliest valid stage within a burst. This is
determined as if an explicit Precharge command was issued at the earliest possible time without violating tRAS(min). The user
must not issue another command to the same bank until the precharge (tRP) is completed.
The NTC DDR SDRAM devices supports the optional tRAS lockout feature. This feature allows a Read command with Auto Pre-
charge to be issued to a bank that has been activated (opened) but has not yet satisfied the tRAS(min) specification. The tRAS
lockout feature essentially delays the onset of the auto precharge operation until two conditions occur. One, the entire burst
length of data has been successfully prefetched from the memory array; and two, tRAS(min) has been satisfied.
As a means to specify whether a DDR SDRAM device supports the tRAS lockout feature, a new parameter has been defined,
tRAP (RAS Command to Read Command with Auto Precharge or better stated Bank Activate to Read Command with Auto Pre-
charge). For devices that support the tRAS lockout feature, tRAP = tRCD(min). This allows any Read Command (with or without
Auto Precharge) to be issued to an open bank once tRCD(min) is satisfied.
Burst Terminate
The Burst Terminate command is used to truncate read bursts (with Auto Precharge disabled). The most re-cently registered
Read command prior to the Burst Terminate command is truncated, as shown in the Operation section of this data sheet. Write
burst cycles are not to be terminated with the Burst Terminate command.
tRAP Definition
CK
Command
DQ (BL=2)
tRAPmin
NOP
ACT
NOP
RD A
NOP
ACT
NOP
tRCDmin
tRASmin
DQ0 DQ1
The above timing diagrams show the effects of tRAP for devices that support tRAS lockout. In these cases, the Read
with Auto Precharge command (RDA) is issued with tRCD(min) and dataout is available with the shortest latency from the
Bank Activate command (ACT). The internal precharge operation, however, does not begin until after tRAS(min) is satisfied.
CL=2, tCK=10ns
Command
DQ (BL=4)
NOP
ACT
NOP
RD A
NOP
ACT
NOP
DQ0 DQ1 DQ2 DQ3
Command
DQ (BL=8)
NOP
ACT
NOP
RD A
NOP
ACT
NOP
DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7
*
*IndicatesAutoPrechargebeginshere
tRPmin
相关PDF资料 |
PDF描述 |
|---|---|
| NT5SE8M16DS-6K | 8M X 16 SYNCHRONOUS DRAM, 5 ns, PDSO54 |
| NT5SV8M8DT-7 | 8M X 8 SYNCHRONOUS DRAM, 5.4 ns, PDSO54 |
| NTC1111-20MHZ | Analog IC |
| NTC1111-SERIES | Analog IC |
| NTC1120-12.8MHZ | Analog IC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NT5S10001BA20 | 功能描述:金属膜电阻器 - 透孔 NT5 S 10K 0,1% AM500 e3 RoHS:否 制造商:IRC 电阻:63.4 kOhms 容差:1 % 功率额定值:100 mW 电压额定值:200 V 温度系数:100 PPM / C 端接类型:Axial 工作温度范围: 尺寸:2.3 mm Dia. x 6.4 mm L 封装:Bulk |
| NT5S10001FA20 | 功能描述:金属膜电阻器 - 透孔 NT5 S 10K 1% AM500 e3 RoHS:否 制造商:IRC 电阻:63.4 kOhms 容差:1 % 功率额定值:100 mW 电压额定值:200 V 温度系数:100 PPM / C 端接类型:Axial 工作温度范围: 尺寸:2.3 mm Dia. x 6.4 mm L 封装:Bulk |
| NT5S10002BA20 | 功能描述:金属膜电阻器 - 透孔 NT5 S 100K 0,1% AM500 e3 RoHS:否 制造商:IRC 电阻:63.4 kOhms 容差:1 % 功率额定值:100 mW 电压额定值:200 V 温度系数:100 PPM / C 端接类型:Axial 工作温度范围: 尺寸:2.3 mm Dia. x 6.4 mm L 封装:Bulk |
| NT5S131R6BA20 | 功能描述:金属膜电阻器 - 透孔 NT5 S 131U6 0,1% AM500 e3 RoHS:否 制造商:IRC 电阻:63.4 kOhms 容差:1 % 功率额定值:100 mW 电压额定值:200 V 温度系数:100 PPM / C 端接类型:Axial 工作温度范围: 尺寸:2.3 mm Dia. x 6.4 mm L 封装:Bulk |
| NT5S15000FA20 | 功能描述:金属膜电阻器 - 透孔 NT5 S 1K5 1% AM500 e3 RoHS:否 制造商:IRC 电阻:63.4 kOhms 容差:1 % 功率额定值:100 mW 电压额定值:200 V 温度系数:100 PPM / C 端接类型:Axial 工作温度范围: 尺寸:2.3 mm Dia. x 6.4 mm L 封装:Bulk |
发布紧急采购，3分钟左右您将得到回复。