参数资料
型号: PCA9698DGG,512
厂商: NXP Semiconductors
文件页数: 20/48页
文件大小: 0K
描述: IC I/O EXPANDER I2C 40B 56TSSOP
产品培训模块: I²C Bus Fundamentals
特色产品: NXP - I2C Interface
标准包装: 35
接口: I²C
输入/输出数: 40
中断输出:
频率 - 时钟: 1MHz
电源电压: 2.3 V ~ 5.5 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 56-TFSOP(0.240",6.10mm 宽)
供应商设备封装: 56-TSSOP
包装: 管件
包括: POR
产品目录页面: 826 (CN2011-ZH PDF)
其它名称: 568-3241-5
935278614512
PCA9698DGG
27
7810C–AVR–10/12
Atmel ATmega328P [Preliminary]
selectable delays are shown in Table 8-2. The frequency of the Watchdog Oscillator is voltage
Main purpose of the delay is to keep the AVR in reset until it is supplied with minimum V
CC. The
delay will not monitor the actual voltage and it will be required to select a delay longer than the
V
CC rise time. If this is not possible, an internal or external Brown-Out Detection circuit should be
used. A BOD circuit will ensure sufficient V
CC before it releases the reset, and the time-out delay
can be disabled. Disabling the time-out delay without utilizing a Brown-Out Detection circuit is
not recommended.
The oscillator is required to oscillate for a minimum number of cycles before the clock is consid-
ered stable. An internal ripple counter monitors the oscillator output clock, and keeps the internal
reset active for a given number of clock cycles. The reset is then released and the device will
start to execute. The recommended oscillator start-up time is dependent on the clock type, and
varies from 6 cycles for an externally applied clock to 32K cycles for a low frequency crystal.
The start-up sequence for the clock includes both the time-out delay and the start-up time when
the device starts up from reset. When starting up from Power-save or Power-down mode, V
CC is
assumed to be at a sufficient level and only the start-up time is included.
8.3
Low Power Crystal Oscillator
Pins XTAL1 and XTAL2 are input and output, respectively, of an inverting amplifier which can be
configured for use as an On-chip Oscillator, as shown in Figure 8-2 on page 28. Either a quartz
crystal or a ceramic resonator may be used.
This Crystal Oscillator is a low power oscillator, with reduced voltage swing on the XTAL2 out-
put. It gives the lowest power consumption, but is not capable of driving other clock inputs, and
may be more susceptible to noise in noisy environments. In these cases, refer to the “Full Swing
C1 and C2 should always be equal for both crystals and resonators. The optimal value of the
capacitors depends on the crystal or resonator in use, the amount of stray capacitance, and the
electromagnetic noise of the environment. Some initial guidelines for choosing capacitors for
use with crystals are given in Table 8-3 on page 28. For ceramic resonators, the capacitor val-
ues given by the manufacturer should be used.
Table 8-2.
Number of Watchdog Oscillator Cycles
Typ Time-out (VCC = 5.0V)
Typ Time-out (VCC = 3.0V)
Number of Cycles
0 ms
0
4.1 ms
4.3 ms
512
65 ms
69 ms
8K (8,192)
相关PDF资料
PDF描述
PCA9506DGG,512 IC I/O EXPANDER I2C 40B 56TSSOP
PCA9505DGG,112 IC I/O EXPANDER I2C 40B 56TSSOP
ATTINY13-20MUR IC MCU AVR 1K FLASH 10MHZ 20MLF
5-530520-1 CONT.HIGH CURRENT L.P.
5-583875-6 TWIN LEAF CONTACT
相关代理商/技术参数
参数描述
PCA9698DGGS911,51 功能描述:I2C 接口集成电路 40-bit Fm I2C Bus I/O port w/Reset RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16
PCA9698DGGT 制造商:NXP Semiconductors 功能描述:I2C GPIO Expander 5.5V 56-Pin TSSOP T/R
PCA9698DGG-T 制造商:NXP Semiconductors 功能描述:I2C GPIO Expander 5.5V 56-Pin TSSOP T/R
PCA96PWS911,118 功能描述:接口-I/O扩展器 8-BIT I2C FM QB RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel
PCA9701D 功能描述:寄存器 16BIT SPI 18V GPI INT -40 +125 RoHS:否 制造商:NXP Semiconductors 逻辑类型:CMOS 逻辑系列:HC 电路数量:1 最大时钟频率:36 MHz 传播延迟时间: 高电平输出电流:- 7.8 mA 低电平输出电流:7.8 mA 电源电压-最大:6 V 最大工作温度:+ 125 C 封装 / 箱体:SOT-38 封装:Tube