参数资料
型号: PCA9698DGG,512
厂商: NXP Semiconductors
文件页数: 22/48页
文件大小: 0K
描述: IC I/O EXPANDER I2C 40B 56TSSOP
产品培训模块: I²C Bus Fundamentals
特色产品: NXP - I2C Interface
标准包装: 35
接口: I²C
输入/输出数: 40
中断输出:
频率 - 时钟: 1MHz
电源电压: 2.3 V ~ 5.5 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 56-TFSOP(0.240",6.10mm 宽)
供应商设备封装: 56-TSSOP
包装: 管件
包括: POR
产品目录页面: 826 (CN2011-ZH PDF)
其它名称: 568-3241-5
935278614512
PCA9698DGG
29
7810C–AVR–10/12
Atmel ATmega328P [Preliminary]
Notes:
1. These options should only be used when not operating close to the maximum frequency of the
device, and only if frequency stability at start-up is not important for the application. These
options are not suitable for crystals.
2. These options are intended for use with ceramic resonators and will ensure frequency stability
at start-up. They can also be used with crystals when not operating close to the maximum fre-
quency of the device, and if frequency stability at start-up is not important for the application.
8.4
Full Swing Crystal Oscillator
Pins XTAL1 and XTAL2 are input and output, respectively, of an inverting amplifier which can be
configured for use as an On-chip Oscillator, as shown in Figure 8-2 on page 28. Either a quartz
crystal or a ceramic resonator may be used.
This Crystal Oscillator is a full swing oscillator, with rail-to-rail swing on the XTAL2 output. This is
useful for driving other clock inputs and in noisy environments. The current consumption is
higher than the “Low Power Crystal Oscillator” on page 27. Note that the Full Swing Crystal
Oscillator will only operate for V
CC = 2.7 - 5.5 volts.
C1 and C2 should always be equal for both crystals and resonators. The optimal value of the
capacitors depends on the crystal or resonator in use, the amount of stray capacitance, and the
electromagnetic noise of the environment. Some initial guidelines for choosing capacitors for
use with crystals are given in Table 8-6 on page 30. For ceramic resonators, the capacitor val-
ues given by the manufacturer should be used.
The operating mode is selected by the fuses CKSEL3..1 as shown in Table 8-5.
Notes:
1. The frequency ranges are preliminary values. Actual values are TBD.
2. If 8 MHz frequency exceeds the specification of the device (depends on V
CC), the CKDIV8
Fuse can be programmed in order to divide the internal frequency by 8. It must be ensured
that the resulting divided clock meets the frequency specification of the device.
Crystal Oscillator, BOD
enabled
16K CK
14CK
1
01
Crystal Oscillator, fast
rising power
16K CK
14CK + 4.1 ms
1
10
Crystal Oscillator, slowly
rising power
16K CK
14CK + 65 ms
1
11
Table 8-4.
Start-up Times for the Low Power Crystal Oscillator Clock Selection (Continued)
Oscillator Source /
Power Conditions
Start-up Time from
Power-down and
Power-save
Additional Delay
from Reset
(VCC = 5.0V)
CKSEL0
SUT1..0
Table 8-5.
Full Swing Crystal Oscillator operating modes
Frequency Range(1)
(MHz)
Recommended Range for
Capacitors C1 and C2 (pF)
CKSEL3..1
0.4 - 16
12 - 22
011
相关PDF资料
PDF描述
PCA9506DGG,512 IC I/O EXPANDER I2C 40B 56TSSOP
PCA9505DGG,112 IC I/O EXPANDER I2C 40B 56TSSOP
ATTINY13-20MUR IC MCU AVR 1K FLASH 10MHZ 20MLF
5-530520-1 CONT.HIGH CURRENT L.P.
5-583875-6 TWIN LEAF CONTACT
相关代理商/技术参数
参数描述
PCA9698DGGS911,51 功能描述:I2C 接口集成电路 40-bit Fm I2C Bus I/O port w/Reset RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16
PCA9698DGGT 制造商:NXP Semiconductors 功能描述:I2C GPIO Expander 5.5V 56-Pin TSSOP T/R
PCA9698DGG-T 制造商:NXP Semiconductors 功能描述:I2C GPIO Expander 5.5V 56-Pin TSSOP T/R
PCA96PWS911,118 功能描述:接口-I/O扩展器 8-BIT I2C FM QB RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel
PCA9701D 功能描述:寄存器 16BIT SPI 18V GPI INT -40 +125 RoHS:否 制造商:NXP Semiconductors 逻辑类型:CMOS 逻辑系列:HC 电路数量:1 最大时钟频率:36 MHz 传播延迟时间: 高电平输出电流:- 7.8 mA 低电平输出电流:7.8 mA 电源电压-最大:6 V 最大工作温度:+ 125 C 封装 / 箱体:SOT-38 封装:Tube