参数资料
型号: PCA9698DGG,512
厂商: NXP Semiconductors
文件页数: 26/48页
文件大小: 0K
描述: IC I/O EXPANDER I2C 40B 56TSSOP
产品培训模块: I²C Bus Fundamentals
特色产品: NXP - I2C Interface
标准包装: 35
接口: I²C
输入/输出数: 40
中断输出:
频率 - 时钟: 1MHz
电源电压: 2.3 V ~ 5.5 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 56-TFSOP(0.240",6.10mm 宽)
供应商设备封装: 56-TSSOP
包装: 管件
包括: POR
产品目录页面: 826 (CN2011-ZH PDF)
其它名称: 568-3241-5
935278614512
PCA9698DGG
32
7810C–AVR–10/12
Atmel ATmega328P [Preliminary]
8.6
Calibrated Internal RC Oscillator
By default, the Internal RC Oscillator provides an approximate 8.0 MHz clock. Though voltage
and temperature dependent, this clock can be very accurately calibrated by the user. See Table
28-1 on page 307 for more details. The device is shipped with the CKDIV8 Fuse programmed.
This clock may be selected as the system clock by programming the CKSEL Fuses as shown in
Table 8-10. If selected, it will operate with no external components. During reset, hardware loads
the pre-programmed calibration value into the OSCCAL Register and thereby automatically cal-
ibrates the RC Oscillator. The accuracy of this calibration is shown as Factory calibration in
By changing the OSCCAL register from SW, see “OSCCAL – Oscillator Calibration Register” on
page 35, it is possible to get a higher calibration accuracy than by using the factory calibration.
The accuracy of this calibration is shown as User calibration in Table 28-1 on page 307.
When this Oscillator is used as the chip clock, the Watchdog Oscillator will still be used for the
Watchdog Timer and for the Reset Time-out. For more information on the pre-programmed cali-
bration value, see the section “Calibration Byte” on page 289.
Notes:
1. The device is shipped with this option selected..
2. If 8 MHz frequency exceeds the specification of the device (depends on V
CC), the CKDIV8
Fuse can be programmed in order to divide the internal frequency by 8.
When this Oscillator is selected, start-up times are determined by the SUT Fuses as shown in
Note:
1. If the RSTDISBL fuse is programmed, this start-up time will be increased to
14CK + 4.1 ms to ensure programming mode can be entered.
2.
The device is shipped with this option selected.
8.7
128 kHz Internal Oscillator
The 128 kHz internal Oscillator is a low power Oscillator providing a clock of 128 kHz. The fre-
quency is nominal at 3V and 25°C. This clock may be select as the system clock by
programming the CKSEL Fuses to “11” as shown in Table 8-12..
Table 8-10.
Internal Calibrated RC Oscillator Operating Modes(1)(2)
Nominal Frequency (MHz)
CKSEL3..0
8
0010
Table 8-11.
Start-up times for the internal calibrated RC Oscillator clock selection
Power Conditions
Start-up Time from
Power-down and Power-save
Additional Delay from
Reset (VCC = 5.0V)
SUT1..0
BOD enabled
6 CK
14CK(1)
00
Fast rising power
6 CK
14CK + 4.1 ms
01
Slowly rising power
6 CK
14CK + 65 ms(2)
10
Reserved
11
Table 8-12.
128 kHz Internal Oscillator Operating Modes
Nominal Frequency
CKSEL3..0
128 kHz
0011
相关PDF资料
PDF描述
PCA9506DGG,512 IC I/O EXPANDER I2C 40B 56TSSOP
PCA9505DGG,112 IC I/O EXPANDER I2C 40B 56TSSOP
ATTINY13-20MUR IC MCU AVR 1K FLASH 10MHZ 20MLF
5-530520-1 CONT.HIGH CURRENT L.P.
5-583875-6 TWIN LEAF CONTACT
相关代理商/技术参数
参数描述
PCA9698DGGS911,51 功能描述:I2C 接口集成电路 40-bit Fm I2C Bus I/O port w/Reset RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16
PCA9698DGGT 制造商:NXP Semiconductors 功能描述:I2C GPIO Expander 5.5V 56-Pin TSSOP T/R
PCA9698DGG-T 制造商:NXP Semiconductors 功能描述:I2C GPIO Expander 5.5V 56-Pin TSSOP T/R
PCA96PWS911,118 功能描述:接口-I/O扩展器 8-BIT I2C FM QB RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel
PCA9701D 功能描述:寄存器 16BIT SPI 18V GPI INT -40 +125 RoHS:否 制造商:NXP Semiconductors 逻辑类型:CMOS 逻辑系列:HC 电路数量:1 最大时钟频率:36 MHz 传播延迟时间: 高电平输出电流:- 7.8 mA 低电平输出电流:7.8 mA 电源电压-最大:6 V 最大工作温度:+ 125 C 封装 / 箱体:SOT-38 封装:Tube