参数资料
型号: PIC12F1822-I/MF
厂商: Microchip Technology
文件页数: 23/109页
文件大小: 0K
描述: IC MCU 8BIT FLASH 8DFN
产品培训模块: 8-bit PIC® Microcontroller Portfolio
标准包装: 120
系列: PIC® XLP™ 12F
核心处理器: PIC
芯体尺寸: 8-位
速度: 32MHz
连通性: I²C,LIN,SPI,UART/USART
外围设备: 欠压检测/复位,POR,PWM,WDT
输入/输出数: 6
程序存储器容量: 3.5KB(2K x 14)
程序存储器类型: 闪存
EEPROM 大小: 256 x 8
RAM 容量: 128 x 8
电压 - 电源 (Vcc/Vdd): 1.8 V ~ 5.5 V
数据转换器: A/D 4x10b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 8-VDFN 裸露焊盘
包装: 管件
211
7674F–AVR–09/09
ATmega164P/324P/644P
Figure 19-2. Data Validity
19.3.2
START and STOP Conditions
The Master initiates and terminates a data transmission. The transmission is initiated when the
Master issues a START condition on the bus, and it is terminated when the Master issues a
STOP condition. Between a START and a STOP condition, the bus is considered busy, and no
other master should try to seize control of the bus. A special case occurs when a new START
condition is issued between a START and STOP condition. This is referred to as a REPEATED
START condition, and is used when the Master wishes to initiate a new transfer without relin-
quishing control of the bus. After a REPEATED START, the bus is considered busy until the next
STOP. This is identical to the START behavior, and therefore START is used to describe both
START and REPEATED START for the remainder of this datasheet, unless otherwise noted. As
depicted below, START and STOP conditions are signalled by changing the level of the SDA
line when the SCL line is high.
Figure 19-3. START, REPEATED START and STOP conditions
19.3.3
Address Packet Format
All address packets transmitted on the TWI bus are 9 bits long, consisting of 7 address bits, one
READ/WRITE control bit and an acknowledge bit. If the READ/WRITE bit is set, a read opera-
tion is to be performed, otherwise a write operation should be performed. When a Slave
recognizes that it is being addressed, it should acknowledge by pulling SDA low in the ninth SCL
(ACK) cycle. If the addressed Slave is busy, or for some other reason can not service the Mas-
ter’s request, the SDA line should be left high in the ACK clock cycle. The Master can then
transmit a STOP condition, or a REPEATED START condition to initiate a new transmission. An
address packet consisting of a slave address and a READ or a WRITE bit is called SLA+R or
SLA+W, respectively.
SDA
SCL
Data Stable
Data Change
SDA
SCL
START
STOP
REPEATED START
STOP
START
相关PDF资料
PDF描述
PIC18LC452T-I/L IC MCU OTP 16KX16 A/D 44PLCC
PIC17LC43T-08I/L IC MCU OTP 4KX16 PWM 44PLCC
PIC12F629-I/P IC MCU CMOS FLASH-BASE 8BIT 8DIP
PIC12F675-I/SN IC MCU CMOS FLSH-BASE 8BIT 8SOIC
PIC17LC43T-08/PT IC MCU OTP 4KX16 PWM 44TQFP
相关代理商/技术参数
参数描述
PIC12F1822T-E/SN 制造商:Microchip Technology Inc 功能描述:PIC12F Series 128 B RAM 3.5 kB Flash 8-Bit CMOS Microcontroller - SOIC-8
PIC12F1822T-I/MF 功能描述:8位微控制器 -MCU 3.5KB 128B RAM 32MHz RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC12F1822T-I/SN 功能描述:8位微控制器 -MCU 3.5KB 128B RAM 32MHz Int. Osc 6 I/0 RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC12F1822T-I/SS 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8/14-Pin Flash Microcontrollers with nanoWatt XLP Technology
PIC12F1840 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8-Pin Flash Microcontrollers with nanoWatt XLP Technology