参数资料
| 型号： | PIC12F1822-I/MF |
| 厂商： | Microchip Technology |
| 文件页数： | 91/109页 |
| 文件大小： | 0K |
| 描述： | IC MCU 8BIT FLASH 8DFN |
| 产品培训模块： | 8-bit PIC® Microcontroller Portfolio |
| 标准包装： | 120 |
| 系列： | PIC® XLP™ 12F |
| 核心处理器： | PIC |
| 芯体尺寸： | 8-位 |
| 速度： | 32MHz |
| 连通性： | I²C，LIN，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 6 |
| 程序存储器容量： | 3.5KB（2K x 14） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 256 x 8 |
| RAM 容量： | 128 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.8 V ~ 5.5 V |
| 数据转换器： | A/D 4x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-VDFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页当前第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页
PIC12(L)F1822/PIC16(L)F1823
DS41413C-page 42
2010-2012 Microchip Technology Inc.
3.3
PCL and PCLATH
The Program Counter (PC) is 15 bits wide. The low byte
comes from the PCL register, which is a readable and
writable register. The high byte (PC<14:8>) is not directly
readable or writable and comes from PCLATH. On any
Reset, the PC is cleared. Figure 3-3 shows the five
situations for the loading of the PC.
FIGURE 3-3:
LOADING OF PC IN
DIFFERENT SITUATIONS
3.3.1
MODIFYING PCL
Executing any instruction with the PCL register as the
destination simultaneously causes the Program Coun-
ter PC<14:8> bits (PCH) to be replaced by the contents
of the PCLATH register. This allows the entire contents
of the program counter to be changed by writing the
desired upper 7 bits to the PCLATH register. When the
lower eight bits are written to the PCL register, all 15
bits of the program counter will change to the values
contained in the PCLATH register and those being writ-
ten to the PCL register.
3.3.2
COMPUTED GOTO
A computed GOTO is accomplished by adding an offset to
the program counter (ADDWF PCL). When performing a
table read using a computed GOTO method, care should
be exercised if the table location crosses a PCL memory
boundary (each 256-byte block). Refer to the Application
Note AN556, “Implementing a Table Read” (DS00556).
3.3.3
COMPUTED FUNCTION CALLS
A computed function CALL allows programs to maintain
tables of functions and provide another way to execute
state machines or look-up tables. When performing a
table read using a computed function CALL, care
should be exercised if the table location crosses a PCL
memory boundary (each 256-byte block).
If using the CALL instruction, the PCH<2:0> and PCL
registers are loaded with the operand of the CALL
instruction. PCH<6:3> is loaded with PCLATH<6:3>.
The CALLW instruction enables computed calls by com-
bining PCLATH and W to form the destination address.
A computed CALLW is accomplished by loading the W
register with the desired address and executing CALLW.
The PCL register is loaded with the value of W and
PCH is loaded with PCLATH.
3.3.4
BRANCHING
The branching instructions add an offset to the PC.
This allows relocatable code and code that crosses
page boundaries. There are two forms of branching,
BRW
and BRA. The PC will have incremented to fetch
the next instruction in both cases. When using either
branching instruction, a PCL memory boundary may be
crossed.
If using BRW, load the W register with the desired
unsigned address and execute BRW. The entire PC will
be loaded with the address PC + 1 + W.
If using BRA, the entire PC will be loaded with PC + 1 +,
the signed value of the operand of the BRA instruction.
PCL
PCH
0
14
PC
0
6
7
ALU Result
8
PCLATH
PCL
PCH
0
14
PC
0
6 4
OPCODE <10:0>
11
PCLATH
PCL
PCH
0
14
PC
0
6
7
W
8
PCLATH
Instruction with
PCL as
Destination
GOTO, CALL
CALLW
PCL
PCH
0
14
PC
PC + W
15
BRW
PCL
PCH
0
14
PC
PC + OPCODE <8:0>
15
BRA
相关PDF资料 |
PDF描述 |
|---|---|
| PIC18LC452T-I/L | IC MCU OTP 16KX16 A/D 44PLCC |
| PIC17LC43T-08I/L | IC MCU OTP 4KX16 PWM 44PLCC |
| PIC12F629-I/P | IC MCU CMOS FLASH-BASE 8BIT 8DIP |
| PIC12F675-I/SN | IC MCU CMOS FLSH-BASE 8BIT 8SOIC |
| PIC17LC43T-08/PT | IC MCU OTP 4KX16 PWM 44TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC12F1822T-E/SN | 制造商:Microchip Technology Inc 功能描述:PIC12F Series 128 B RAM 3.5 kB Flash 8-Bit CMOS Microcontroller - SOIC-8 |
| PIC12F1822T-I/MF | 功能描述:8位微控制器 -MCU 3.5KB 128B RAM 32MHz RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC12F1822T-I/SN | 功能描述:8位微控制器 -MCU 3.5KB 128B RAM 32MHz Int. Osc 6 I/0 RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC12F1822T-I/SS | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8/14-Pin Flash Microcontrollers with nanoWatt XLP Technology |
| PIC12F1840 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8-Pin Flash Microcontrollers with nanoWatt XLP Technology |
发布紧急采购，3分钟左右您将得到回复。