- 您现在的位置：买卖IC网 > PDF目录134951 > Q80C32-30SHXXX:RD (TEMIC SEMICONDUCTORS) 8-BIT, 30 MHz, MICROCONTROLLER, CQFP44 PDF资料下载
参数资料
| 型号： | Q80C32-30SHXXX:RD |
| 厂商： | TEMIC SEMICONDUCTORS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, 30 MHz, MICROCONTROLLER, CQFP44 |
| 文件页数： | 42/83页 |
| 文件大小： | 8336K |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页当前第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页
39
8021G–AVR–03/11
ATmega329P/3290P
USI start condition detection, and the Watchdog continue operating (if enabled). Only an Exter-
nal Reset, a Watchdog Reset, a Brown-out Reset, USI start condition interrupt, an external level
interrupt on INT0, or a pin change interrupt can wake up the MCU. This sleep mode basically
halts all generated clocks, allowing operation of asynchronous modules only.
Note that if a level triggered interrupt is used for wake-up from Power-down mode, the changed
level must be held for some time to wake up the MCU. Refer to ”External Interrupts” on page 58
for details.
When waking up from Power-down mode, there is a delay from the wake-up condition occurs
until the wake-up becomes effective. This allows the clock to restart and become stable after
having been stopped. The wake-up period is defined by the same CKSEL Fuses that define the
Reset Time-out period, as described in ”Clock Sources” on page 28.
9.7
Power-save Mode
When the SM2:0 bits are written to 011, the SLEEP instruction makes the MCU enter Power-
save mode. This mode is identical to Power-down, with one exception:
If Timer/Counter2 and/or the LCD controller are enabled, they will keep running during sleep.
The device can wake up from either Timer Overflow or Output Compare event from
Timer/Counter2 if the corresponding Timer/Counter2 interrupt enable bits are set in TIMSK2,
and the Global Interrupt Enable bit in SREG is set. It can also wake up from an LCD controller
interrupt.
If neither Timer/Counter2 nor the LCD controller is running, Power-down mode is recommended
instead of Power-save mode.
The LCD controller and Timer/Counter2 can be clocked both synchronously and asynchronously
in Power-save mode. The clock source for the two modules can be selected independent of
each other. If neither the LCD controller nor the Timer/Counter2 is using the asynchronous
clock, the Timer/Counter Oscillator is stopped during sleep. If neither the LCD controller nor the
Timer/Counter2 is using the synchronous clock, the clock source is stopped during sleep. Note
that even if the synchronous clock is running in Power-save, this clock is only available for the
LCD controller and Timer/Counter2.
9.8
Standby Mode
When the SM2:0 bits are 110 and an external crystal/resonator clock option is selected, the
SLEEP instruction makes the MCU enter Standby mode. This mode is identical to Power-down
with the exception that the Oscillator is kept running. From Standby mode, the device wakes up
in six clock cycles.
9.9
Power Reduction Register
The Power Reduction Register (PRR), ”PRR – Power Reduction Register” on page 43, provides
a method to stop the clock to individual peripherals to reduce power consumption. The current
state of the peripheral is frozen and the I/O registers can not be read or written. Resources used
by the peripheral when stopping the clock will remain occupied, hence the peripheral should in
most cases be disabled before stopping the clock. Waking up a module, which is done by clear-
ing the bit in PRR, puts the module in the same state as before shutdown. Module shutdown can
be used in Idle mode and Active mode to significantly reduce the overall power consumption. In
all other sleep modes, the clock is already stopped. Module shutdown can be used in IDLE
相关PDF资料 |
PDF描述 |
|---|---|
| Q80C32-36:R | 8-BIT, 36 MHz, MICROCONTROLLER, CQFP44 |
| Q80C32-36SHXXX:R | 8-BIT, 36 MHz, MICROCONTROLLER, CQFP44 |
| Q80C32-42:D | 8-BIT, 42 MHz, MICROCONTROLLER, CQFP44 |
| Q80C32-42:R | 8-BIT, 42 MHz, MICROCONTROLLER, CQFP44 |
| Q80C32-42SHXXX:D | 8-BIT, 42 MHz, MICROCONTROLLER, CQFP44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| Q80N-5 | 制造商:POWERBOX 制造商全称:Powerbox 功能描述:0.5 WATTS - 100 - 10KV SINGLE OUTPUT DC/DC INDUSTRIAL |
| Q-810 | 功能描述:交流电源插头和插座 NEMA L5-15P LOCKING DEVICE RoHS:否 制造商:Hirose Connector 产品:Plugs 系列: 电流额定值:3 A 电压额定值:30 V 安装角:Straight 安装风格:Cable 颜色: 端口数量: |
| Q81022511000000 | 制造商:Epson Electronics America Inc 功能描述:TF2-J4DB1 184.3200MHZ |
| Q811 | 制造商:Captive Fastener Corporation 功能描述: |
| Q-812 | 制造商:Qualtek Electronics Corporation 功能描述:NEMA TWIST-LOCK 制造商:Qualtek Electronics Corporation 功能描述:Nema St Blade Twist Lock |
发布紧急采购，3分钟左右您将得到回复。