- 您现在的位置：买卖IC网 > PDF目录134951 > Q80C32-30SHXXX:RD (TEMIC SEMICONDUCTORS) 8-BIT, 30 MHz, MICROCONTROLLER, CQFP44 PDF资料下载
参数资料
| 型号： | Q80C32-30SHXXX:RD |
| 厂商： | TEMIC SEMICONDUCTORS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, 30 MHz, MICROCONTROLLER, CQFP44 |
| 文件页数： | 45/83页 |
| 文件大小： | 8336K |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页当前第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页
41
8021G–AVR–03/11
ATmega329P/3290P
9.10.6
Port Pins
When entering a sleep mode, all port pins should be configured to use minimum power. The
most important is then to ensure that no pins drive resistive loads. In sleep modes where both
the I/O clock (clk
I/O) and the ADC clock (clkADC) are stopped, the input buffers of the device will
be disabled. This ensures that no power is consumed by the input logic when not needed. In
some cases, the input logic is needed for detecting wake-up conditions, and it will then be
enabled. Refer to the section ”Digital Input Enable and Sleep Modes” on page 67 for details on
which pins are enabled. If the input buffer is enabled and the input signal is left floating or have
an analog signal level close to V
CC/2, the input buffer will use excessive power.
For analog input pins, the digital input buffer should be disabled at all times. An analog signal
level close to V
CC/2 on an input pin can cause significant current even in active mode. Digital
input buffers can be disabled by writing to the Digital Input Disable Registers (DIDR1 and
DIDR0). Refer to ”DIDR1 – Digital Input Disable Register 1” on page 212 and ”DIDR0 – Digital
Input Disable Register 0” on page 229 for details.
9.10.7
JTAG Interface and On-chip Debug System
If the On-chip debug system is enabled by the OCDEN Fuse and the chip enter Power down or
Power save sleep mode, the main clock source remains enabled. In these sleep modes, this will
contribute significantly to the total current consumption. There are three alternative ways to
avoid this:
Disable OCDEN Fuse.
Disable JTAGEN Fuse.
Write one to the JTD bit in MCUCR.
The TDO pin is left floating when the JTAG interface is enabled while the JTAG TAP controller is
not shifting data. If the hardware connected to the TDO pin does not pull up the logic level,
power consumption will increase. Note that the TDI pin for the next device in the scan chain con-
tains a pull-up that avoids this problem. Writing the JTD bit in the MCUCR register to one or
leaving the JTAG fuse unprogrammed disables the JTAG interface.
相关PDF资料 |
PDF描述 |
|---|---|
| Q80C32-36:R | 8-BIT, 36 MHz, MICROCONTROLLER, CQFP44 |
| Q80C32-36SHXXX:R | 8-BIT, 36 MHz, MICROCONTROLLER, CQFP44 |
| Q80C32-42:D | 8-BIT, 42 MHz, MICROCONTROLLER, CQFP44 |
| Q80C32-42:R | 8-BIT, 42 MHz, MICROCONTROLLER, CQFP44 |
| Q80C32-42SHXXX:D | 8-BIT, 42 MHz, MICROCONTROLLER, CQFP44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| Q80N-5 | 制造商:POWERBOX 制造商全称:Powerbox 功能描述:0.5 WATTS - 100 - 10KV SINGLE OUTPUT DC/DC INDUSTRIAL |
| Q-810 | 功能描述:交流电源插头和插座 NEMA L5-15P LOCKING DEVICE RoHS:否 制造商:Hirose Connector 产品:Plugs 系列: 电流额定值:3 A 电压额定值:30 V 安装角:Straight 安装风格:Cable 颜色: 端口数量: |
| Q81022511000000 | 制造商:Epson Electronics America Inc 功能描述:TF2-J4DB1 184.3200MHZ |
| Q811 | 制造商:Captive Fastener Corporation 功能描述: |
| Q-812 | 制造商:Qualtek Electronics Corporation 功能描述:NEMA TWIST-LOCK 制造商:Qualtek Electronics Corporation 功能描述:Nema St Blade Twist Lock |
发布紧急采购，3分钟左右您将得到回复。