- 您现在的位置：买卖IC网 > PDF目录192295 > S29AL032D70BAE002 (Spansion Inc.) 32 Megabit CMOS 3.0 Volt-only Flash Memory PDF资料下载
参数资料
| 型号： | S29AL032D70BAE002 |
| 厂商： | Spansion Inc. |
| 英文描述： | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
| 中文描述： | 32兆位的CMOS 3.0伏只闪存 |
| 文件页数： | 28/69页 |
| 文件大小： | 1970K |
| 代理商： | S29AL032D70BAE002 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页
32
S29AL032D
S29AL032D_00_A3 June 13, 2005
Advan ce
In form ati o n
Reset Command
Writing the reset command to the device resets the device to reading array data. Address bits are
don’t care for this command.
The reset command may be written between the sequence cycles in an erase command sequence
before erasing begins. This resets the device to reading array data. Once erasure begins, however,
the device ignores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in a program command se-
quence before programming begins. This resets the device to reading array data (also applies to
programming in Erase Suspend mode). Once programming begins, however, the device ignores
reset commands until the operation is complete.
The reset command may be written between the sequence cycles in an autoselect command se-
quence. Once in the autoselect mode, the reset command must be written to return to reading
array data (also applies to autoselect during Erase Suspend).
If DQ5 goes high during a program or erase operation, writing the reset command returns the
device to reading array data (also applies during Erase Suspend).
Autoselect Command Sequence
The autoselect command sequence allows the host system to access the manufacturer and de-
vices codes, and determine whether a sector is protected. Table 17 on page 38 shows the address
and data requirements. This method is an alternative to that shown in Table 8 on page 20, which
is intended for PROM programmers and requires VID on address bit A9.
The autoselect command sequence is initiated by writing two unlock cycles, followed by the au-
toselect command. The device then enters the autoselect mode, and the system may read at any
address any number of times, without initiating another command sequence.
A read cycle at address 0XXX00h retrieves the manufacturer code. A read cycle at address
0XXX01h returns the device code. A read cycle containing a sector address (SA) and the address
02h in word mode (or 04h in byte mode) returns 01h if that sector is protected, or 00h if it is
unprotected. Refer to Table 2 on page 14 and Table 4 on page 16 for valid sector addresses.
The system must write the reset command to exit the autoselect mode and return to reading
array data.
Enter Secured Silicon Sector/Exit Secured Silicon Sector
Command Sequence
The Secured Silicon Sector region provides a secured data area containing a random, sixteen-
byte electronic serial number (ESN). The system can access the Secured Silicon Sector region by
issuing the three-cycle Enter Secured Silicon Sector command sequence. The device continues to
access the Secured Silicon Sector region until the system issues the four-cycle Exit Secured Sili-
con Sector command sequence. The Exit Secured Silicon Sector command sequence returns the
device to normal operation. Table 16. S29AL032D Command Definitions — Model 00 on page 37
and Table 17. S29AL032D Command Definitions — Models 03, 04 on page 38 show the ad-
dresses and data requirements for both command sequences. Note that the ACC function and
unlock bypass modes are not available when the device enters the Secured Silicon Sector. See
also Secured Silicon Sector Flash Memory Region on page 26 for further information.
Word/Byte Program Command Sequence
Models 03, 04 may program the device by word or byte, depending on the state of the BYTE#
pin. Model 00 may program the device by byte only. Programming is a four-bus-cycle operation.
The program command sequence is initiated by writing two unlock write cycles, followed by the
program set-up command. The program address and data are written next, which in turn initiate
相关PDF资料 |
PDF描述 |
|---|---|
| S29AL032D90TFI042 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
| S29AL032D90TFI043 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
| S29CD016G0JDEI004 | 512K X 32 FLASH 2.7V PROM, 67 ns, UUC76 |
| S29CD016G0JDEI007 | 512K X 32 FLASH 2.7V PROM, 67 ns, UUC76 |
| S29CD032J1JFAI122 | 1M X 32 FLASH 2.7V PROM, 54 ns, PBGA80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S29AL032D70BAI000 | 制造商:Spansion 功能描述:NOR Flash Parallel 3.3V 32Mbit 4M x 8bit 70ns 48-Pin FBGA Tray |
| S29AL032D70BAI030 | 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 32Mbit 4M/2M x 8bit/16bit 70ns 48-Pin FBGA Tray |
| S29AL032D70BAI032 | 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 32Mbit 4M/2M x 8bit/16bit 70ns 48-Pin FBGA T/R |
| S29AL032D70BFI000 | 功能描述:闪存 32MB 闪存 3V 70ns Parallel NOR 闪存 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| S29AL032D70BFI030 | 功能描述:闪存 32MB 闪存 3V 70ns Parallel NOR 闪存 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。