- 您现在的位置：买卖IC网 > PDF目录225148 > SC9RS08KA1J3CDB (FREESCALE SEMICONDUCTOR INC) 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDSO6 PDF资料下载
参数资料
| 型号： | SC9RS08KA1J3CDB |
| 厂商： | FREESCALE SEMICONDUCTOR INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDSO6 |
| 封装： | 3 X 3 MM, 0.80 MM HEIGHT, ROHS COMPLIANT, DFN-6 |
| 文件页数： | 46/134页 |
| 文件大小： | 3114K |
| 代理商： | SC9RS08KA1J3CDB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页当前第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页
Chapter 2 Pins and Connections
SC9RS08KA2 Series Data Sheet, Rev. 1
Freescale Semiconductor
19
2.4.1
Power
VDD and VSS are the primary power supply pins for the MCU. This voltage source supplies power to all I/O
buffer circuitry and to an internal voltage regulator. The internal voltage regulator provides a regulated
lower-voltage source to the CPU and other internal circuitry of the MCU.
Typically, application systems have two separate capacitors across the power pins: a bulk electrolytic
capacitor, such as a 10-
μF tantalum capacitor, to provide bulk charge storage for the overall system, and a
bypass capacitor, such as a 0.1-
μF ceramic capacitor, located as near to the MCU power pins as practical
to suppress high-frequency noise.
2.4.2
PTA2/KBIP2/TCLK/RESET/VPP
After a power-on reset (POR) into user mode, the PTA2/KBIP2/TCLK/RESET/VPP pin defaults to a
general-purpose input port pin, PTA2. Setting RSTPE in SOPT configures the pin to be the RESET input
pin. After configured as RESET, the pin will remain as RESET until the next POR. The RESET pin can
be used to reset the MCU from an external source when the pin is driven low. When enabled as the RESET
pin (RSTPE = 1), the internal pullup device is automatically enabled.
External VPP voltage (typically 12 V, see Section A.10, “FLASH Specifications”) is required on this pin
when performing Flash programming or erasing. The VPP connection is always connected to the internal
Flash module regardless of the pin function. To avoid over stressing the Flash, external VPP voltage must
be removed and voltage higher than VDD must be avoided when Flash programming or erasing is not
taking place.
NOTE
This pin does not contain a clamp diode to VDD and should not be driven
above VDD when Flash programming or erasing is not taking place.
2.4.3
PTA3/ACMPO/BKGD/MS
The background / mode select function is shared with an output-only pin on PTA3 pin and the optional
analog comparator output. While in reset, the pin functions as a mode select pin. Immediately after reset
rises, the pin functions as the background pin and can be used for background debug communication.
While functioning as a background / mode select pin, this pin has an internal pullup device enabled. To use
as an output-only port, BKGDPE in SOPT must be cleared.
If nothing is connected to this pin, the MCU will enter normal operating mode at the rising edge of reset.
If a debug system is connected to the 6-pin standard background debug header, it can hold BKGD/MS low
during the power-on-reset, which forces the MCU to active background mode.
The BKGD pin is used primarily for background debug controller (BDC) communications using a custom
protocol that uses 16 clock cycles of the target MCU’s BDC clock per bit time. The target MCU’s BDC
clock equals the bus clock rate; therefore, no significant capacitance should connected to the BKGD/MS
pin that could interfere with background serial communications.
Although the BKGD pin is a pseudo open-drain pin, the background debug communication protocol
provides brief, actively driven, high speedup pulses to ensure fast rise times. Small capacitances from
相关PDF资料 |
PDF描述 |
|---|---|
| SCA-6 | 0 MHz - 3000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| SCA1N3595US | 0.125 A, 125 V, SILICON, SIGNAL DIODE |
| SCD0705T-6R8M-N | 1 ELEMENT, 6.8 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| SCD0705T-6R8L-N | 1 ELEMENT, 6.8 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| SCD0705T-6R8K-N | 1 ELEMENT, 6.8 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC9RS08KA1J3CPC | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:RS08 Microcontrollers |
| SC9RS08KA1J3CSC | 制造商:Freescale Semiconductor 功能描述:8-BIT RS08 CISC 1KB FLASH 2.5V/3.3V/5V 8-PIN SOIC N RAIL - Rail/Tube 制造商:Freescale Semiconductor 功能描述:1K FLASH W/ ACMP 62 RAM |
| SC9RS08KA2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:RS08 Microcontrollers |
| SC9RS08KA2J3CDB | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:RS08 Microcontrollers |
| SC9RS08KA2J3CPC | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:RS08 Microcontrollers |
发布紧急采购，3分钟左右您将得到回复。