参数资料
型号: W25Q16BVSSIG
厂商: Winbond Electronics
文件页数: 12/68页
文件大小: 0K
描述: IC SPI FLASH 16MBIT 8SOIC
标准包装: 90
系列: SpiFlash®
格式 - 存储器: 闪存
存储器类型: FLASH
存储容量: 16M(2M x 8)
速度: 104MHz
接口: SPI 串行
电源电压: 2.7 V ~ 3.6 V
工作温度: -40°C ~ 85°C
封装/外壳: 8-SOIC(0.209",5.30mm 宽)
供应商设备封装: 8-SOIC
包装: 管件
W25Q16BV
10.2 WRITE PROTECTION
Applications that use non-volatile memory must take into consideration the possibility of noise and other
adverse system conditions that may compromise data integrity. To address this concern the W25Q16BV
provides several means to protect data from inadvertent writes.
10.2.1 Write Protect Features
?
?
?
?
?
?
?
Device resets when VCC is below threshold
Time delay write disable after Power-up
Write enable/disable instructions and automatic write disable after program and erase
Software and Hardware (/WP pin) write protection using Status Register
Write Protection using Power-down instruction
Lock Down write protection until next power-up (1)
One Time Program (OTP) write protection (1)
Note 1: These features are available upon special order. Please refer to Ordering Information.
Upon power-up or at power-down, the W25Q16BV will maintain a reset condition while VCC is below the
threshold value of V WI , (See Power-up Timing and Voltage Levels and Figure 32). While reset, all
operations are disabled and no instructions are recognized. During power-up and after the VCC voltage
exceeds V WI , all program and erase related instructions are further disabled for a time delay of t PUW . This
includes the Write Enable, Page Program, Sector Erase, Block Erase, Chip Erase and the Write Status
Register instructions. Note that the chip select pin (/CS) must track the VCC supply level at power-up until
the VCC-min level and t VSL time delay is reached. If needed a pull-up resister on /CS can be used to
accomplish this.
After power-up the device is automatically placed in a write-disabled state with the Status Register Write
Enable Latch (WEL) set to a 0. A Write Enable instruction must be issued before a Page Program, Sector
Erase, Chip Erase or Write Status Register instruction will be accepted. After completing a program,
erase or write instruction the Write Enable Latch (WEL) is automatically cleared to a write-disabled state
of 0.
Software controlled write protection is facilitated using the Write Status Register instruction and setting
the Status Register Protect (SRP0, SRP1) and Block Protect (SEC,TB, BP2, BP1 and BP0) bits. These
settings allow a portion or all of the memory to be configured as read only. Used in conjunction with the
Write Protect (/WP) pin, changes to the Status Register can be enabled or disabled under hardware
control. See Status Register for further information. Additionally, the Power-down instruction offers an
extra level of write protection as all instructions are ignored except for the Release Power-down
instruction.
- 12 -
相关PDF资料
PDF描述
ASM28DRKH-S13 CONN EDGECARD 56POS .156 EXTEND
RSC65DRES-S734 CONN EDGECARD 130POS .100 EYELET
RMC65DRES-S734 CONN EDGECARD 130PS .100 EYELET
HSC36DRAI-S734 CONN EDGECARD 72POS .100 R/A PCB
AMC28DRTI-S734 CONN EDGECARD 56POS DIP .100 SLD
相关代理商/技术参数
参数描述
W25Q16BVSSIG TR 制造商:Winbond Electronics Corp 功能描述:SPIFLASH, 16M-BIT, 4KB UNIFORM 制造商:Winbond 功能描述:SPIFLASH, 16M-BIT, 4KB UNIFORM
W25Q16BVSSIP 制造商:WINBOND 制造商全称:Winbond 功能描述:16M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
W25Q16BVZPIG 功能描述:IC SPI FLASH 16MBIT 8WSON RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:2,500 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?(单线) 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP,8-MSOP(0.118",3.00mm 宽) 供应商设备封装:8-MSOP 包装:带卷 (TR)
W25Q16BVZPIP 制造商:WINBOND 制造商全称:Winbond 功能描述:16M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
W25Q16CL 制造商:WINBOND 制造商全称:Winbond 功能描述:2.5V 16M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI