参数资料
型号: WJLXT971ALE.A4-857346
厂商: CORTINA SYSTEMS INC
元件分类: 网络接口
英文描述: DATACOM, ETHERNET TRANSCEIVER, PQFP64
封装: 10 X 10 MM, 1.40 MM HEIGHT, ROHS COMPLIANT, LQFP-64
文件页数: 24/80页
文件大小: 931K
代理商: WJLXT971ALE.A4-857346
Page 30
Cortina Systems LXT972A Single-Port 10/100 Mbps PHY Transceiver
LXT972A PHY
Datasheet
249186, Revision 5.2
13 September 2007
5.6 MII Operation
The Next Page exchange uses Register 7 to send information and Register 8 to receive it.
Next Page exchange occurs only if both ends of the link partners advertise their ability to
exchange Next Pages. register bit 6.1 is used to make manual next page exchange easier
for software. This register bit is cleared when a new negotiation occurs, preventing the
user from reading an old value in Register 6 and assuming there is valid information in
Registers 5 and 8.
5.5.1.3
Controlling Auto-Negotiation
When auto-negotiation is controlled by software, Cortina recommends the following steps:
1. After power-up, power-down, or reset, the power-down recovery time (specified in
exhausted before proceeding.
2. Set the Auto-Negotiation Advertisement register bits.
3. Enable auto-negotiation. (Set MDIO register bit 0.12 = 1.)
4. To ensure proper operation, enable or restart auto-negotiation as soon as possible
after writing to Register 4.
5.5.2
Parallel Detection
In parallel with auto-negotiation, the LXT972A PHY also monitors for 10 Mbps Normal
Link Pulses (NLP) or 100 Mbps Idle symbols. If either symbol is detected, the device
automatically reverts to the corresponding speed in half-duplex mode. Parallel detection
allows the LXT972A PHY to communicate with devices that do not support auto-
negotiation.
When parallel detection resolves a link, the link must be established in half-duplex mode.
According to IEEE standards, the forced link partner cannot be configured to full-duplex. If
the auto-negotiation link partner does not advertise half-duplex capability at the speed of
the forced link partner, link is not established. The IEEE Standard prevents full-duplex-to-
half-duplex link connections.
5.6
MII Operation
This section includes the following topics:
The LXT972A PHY implements the Media Independent Interface (MII) as defined by the
IEEE 802.3 standard. Separate channels are provided for transmitting data from the MAC
to the LXT972A PHY (TXD), and for passing data received from the line (RXD) to the
MAC. Each channel has its own clock, data bus, and control signals.
The following signals are used to pass received data to the MAC:
COL
相关PDF资料
PDF描述
WJLXT972ALC.A4-857341 DATACOM, ETHERNET TRANSCEIVER, PQFP64
WJLXT972ALC.A4-857345 DATACOM, ETHERNET TRANSCEIVER, PQFP64
WJLXT971ALC.A4SE000 DATACOM, ETHERNET TRANSCEIVER, PQFP64
WJLXT971ALC.A4SE001 DATACOM, ETHERNET TRANSCEIVER, PQFP64
WJLXT971ALE.A4SE000 DATACOM, ETHERNET TRANSCEIVER, PQFP64
相关代理商/技术参数
参数描述
WJLXT971CA4 制造商:Intel 功能描述:
WJLXT972ALC.A4 功能描述:IC TRANS 3.3V ETHERNET 64-LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器,接收器,收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:25 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:16-DIP(0.300",7.62mm) 供应商设备封装:16-PDIP 包装:管件
WJLXT972ALC.A4 S E001 制造商:Intel 功能描述:PHY 1-CH 10Mbps/100Mbps 64-Pin LQFP T/R
WJLXT972ALC.A4-857341 功能描述:TXRX ETH 10/100 SGL PORT 64-LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器,接收器,收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:收发器 驱动器/接收器数:1/1 规程:RS422,RS485 电源电压:4.75 V ~ 5.25 V 安装类型:通孔 封装/外壳:8-DIP(0.300",7.62mm) 供应商设备封装:8-PDIP 包装:管件 产品目录页面:1402 (CN2011-ZH PDF)
WJLXT972ALC.A4-857345 功能描述:TXRX ETH 10/100 SGL PORT 64-LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器,接收器,收发器 系列:- 标准包装:1 系列:- 类型:线路收发器 驱动器/接收器数:5/3 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC(0.295",7.50mm 宽) 供应商设备封装:28-SOIC 包装:Digi-Reel® 产品目录页面:918 (CN2011-ZH PDF) 其它名称:296-25096-6