参数资料
型号: XR17V252IM-0A-EVB
厂商: Exar Corporation
文件页数: 34/69页
文件大小: 0K
描述: EVAL BOARD FOR XR17V252 100TQFP
标准包装: 1
系列: *
XR17V252
4
66 MHZ PCI BUS DUAL UART WITH POWER MANAGEMENT SUPPORT
REV. 1.0.2
DSR0#
68
I
UART channel 0 Data Set Ready or general purpose input (active low). This
input should be connected to VCC when not used.
CD0#
69
I
UART channel 0 Carrier Detect or general purpose input (active low). This
input should be connected to VCC when not used.
RI0#
70
I
UART channel 0 Ring Indicator or general purpose input (active low). This
input should be connected to VCC when not used.
TX1
62
O
UART channel 1 Transmit Data or infrared transmit data. Normal TXD output
idles HIGH while infrared TXD output idles LOW.
RX1
55
I
UART channel 1 Receive Data or infrared receive data. Normal RXD input
idles HIGH while infrared RXD input idles LOW. In the infrared mode, the
polarity of the incoming RXD signal can be selected via FCTR bit-4. If this bit
is a logic 0, a LOW on the RXD input is considered a mark and if this bit is a
logic 1, a HIGH on the RXD input is considered a space.
RTS1#
60
O
UART channel 1 Request to Send or general purpose output (active low). If
this output is not used, leave it unconnected.
CTS1#
56
I
UART channel 1 Clear to Send or general purpose input (active low). This
input should be connected to VCC when not used.
DTR1#
61
O
UART channel 1 Data Terminal Ready or general purpose output (active
low). If this output is not used, leave it unconnected.
DSR1#
57
I
UART channel 1 Data Set Ready or general purpose input (active low). This
input should be connected to VCC when not used.
CD1#
58
I
UART channel 1 Carrier Detect or general purpose input (active low). This
input should be connected to VCC when not used.
RI1#
59
I
UART channel 1 Ring Indicator or general purpose input (active low). This
input should be connected to VCC when not used.
ANCILLARY SIGNALS
MPIO0-MPIO7
52-45
I/O
Multi-purpose inputs/outputs 0-7. The function of these pin are defined thru
the Configuration Register MPIOSEL, MPIOLVL, MPIOINV, MPIO3T and
MPIOINT
EECK
84
O
Serial clock to EEPROM. An internal clock of CLK divide by 256 is used for
reading the vendor and sub-vendor ID during power up or reset. However, it
can be manually clocked thru the Configuration Register REGB.
EECS
83
O
Chip select to a EEPROM device like 93C46. It is manually selectable thru
the Configuration Register REGB. Requires a pull-up 4.7K ohm resister for
external sensing of EEPROM during power up. See DAN112 for further
details.
EEDI
82
O
Write data to EEPROM device. It is manually accessible thru the Configura-
tion Register REGB. The V252 auto-configuration register interface logic
uses the 16-bit format.
EEDO
81
I
Read data from EEPROM device. It is manually accessible thru the Configu-
ration Register REGB.
XTAL1
77
I
Crystal or external clock input.
XTAL2
76
O
Crystal or buffered clock output.
TMRCK
75
I
16-bit timer/counter external clock input.
PIN DESCRIPTIONS
NAME
PIN #TYPE
DESCRIPTION
相关PDF资料
PDF描述
6278890-4 C/A 62.5 OFNR MTRJ-MTRJ RED SEC
6374656-4 C/A LC TO LC MM 2.0MM 4M
VE-J5R-EX CONVERTER MOD DC/DC 7.5V 75W
RBC26DRXN CONN EDGECARD 52POS DIP .100 SLD
RBM15DTMN CONN EDGECARD 30POS R/A .156 SLD
相关代理商/技术参数
参数描述
XR17V252IM-F 功能描述:UART 接口集成电路 66MHz Dual PCI UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR17V252IMTR-F 制造商:Exar Corporation 功能描述:UART 2-CH 64Byte FIFO 3.3V 100-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR17V252IMTR-F
XR17V254 制造商:EXAR 制造商全称:EXAR 功能描述:66MHZ PCI BUS QUAD UART WITH POWER MANAGEMENT SUPPORT
XR17V254_08 制造商:EXAR 制造商全称:EXAR 功能描述:66MHZ PCI BUS QUAD UART WITH POWER MANAGEMENT SUPPORT
XR17V254IV 制造商:EXAR 制造商全称:EXAR 功能描述:66MHZ PCI BUS QUAD UART WITH POWER MANAGEMENT SUPPORT