参数资料
| 型号： | XRT72L71IQ |
| 厂商： | Exar Corporation |
| 文件页数： | 92/102页 |
| 文件大小： | 0K |
| 描述： | IC FRAMER DS3 ATM UNI 160PQFP |
| 产品变化通告： | XRT72Lx Series Obsolescence 02/May/2012 |
| 标准包装： | 24 |
| 控制器类型： | DS3 ATM UNI，透明通道调帧器 |
| 电源电压： | 3.3V |
| 电流 - 电源： | 120mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 160-BQFP |
| 供应商设备封装： | 160-PQFP（28x28） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页当前第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页
á
XRT72L71
DS3 ATM UNI/CLEAR CHANNEL FRAMER
REV. 1.1.0
5
8RLOL
I
Receive Loss of Lock Indicator—from the XRT7300 E3/DS3/STS-1 LIU IC:
This input pin is intended to be connected to the RLOL (Receive Loss of Lock)
output pin of the XRT7300 LIU IC. The user can monitor the state of this pin by
reading the state of Bit 1 (RLOL) within the Line Interface Scan Register
(Address = 0x73). If this input pin is “Low”, then it means that the phase-locked-
loop circuitry, within the XRT7300 is properly locked onto the incoming DS3
data-stream; and is properly recovering clock and data from this DS3 data-
stream. However, if this input pin is “High”, then it means that the phase-
locked-loop circuitry, within the XRT7300 has lost lock with the incoming DS3
data-stream, and is not properly recovering clock and data.
For more information on the operation of the XRT7300 E3/DS3/STS-1 LIU IC,
please consult the "XRT7300 E3/DS3/STS-1 LIU IC" data sheet.
NOTE: If the designer is not using the XRT7300 DS3/E3/STS-1 LIU IC, this
input pin can be used for other purposes.
9D11
I/O
Bi-Directional Data bus (Microprocessor Interface Section): This pin is
inactive if the Microprocessor Interface block is configured to operate over an
8-bit wide data bus. Please see description for D15, pin 1.
10
TxFrame
O
Transmit End of DS3 Frame Indicator:
The function of this pin is same in both Clear Channel and ATM UNI modes of
the XRT72L71. This pin marks the end of each DS3 frame.
ATM UNI Mode
This pin is pulsed for one DS3 clock period when the transmit input interface
is processing the last bit of the given DS3 frame. This just serves as an indica-
tion to terminal equpiment in the ATM UNI mode.
Clear Channel Mode
When the XRT72L71is configured to operate in the “Clear-Channel Framer”
mode, then the Transmit DS3 Framer block will pulse this output pin “High” (for
one bit period) when the “Transmit Payload Data Input Interface” block is pro-
cessing the last bit of a given DS3 frame.
The purpose of this output pin is to alert the Terminal Equipment that it needs
to begin transmission of a new DS3 frame to the XRT72L71 (e.g., to permit
the XRT72L71 to maintain Transmit DS3 framing alignment control over the
Terminal Equipment).
11
D10
I/O
Bi-Directional Data bus (Microprocessor Interface Section): This pin is
inactive if the Microprocessor Interface block is configured to operate over an
8 bit data bus. (Please see description for D15, pin 1)
12
Req
O
Receive Equalization Bypass Control Output Pin—(to be connected to
the XRT7300 E3/DS3/STS-1 LIU IC): This output pin is intended to be con-
nected to the Req input pin of the XRT7300 E3/DS3/STS-1 LIU IC. The user can
control the state of this output pin by writing a ‘0’ or ‘1’ to Bit 5 (Req) of the
Line Interface Driver Register (Address = 0x72). If the user commands this
signal to toggle “High” then it will cause the incoming DS3 line signal to “by-
pass” equalization circuitry, within the XRT7300. Conversely, if the user com-
mands this output signal to toggle “Low”, then the incoming DS3 line signal
with be routed through the equalization circuitry. For information on the criteria
that should be used when deciding whether to bypass the equalization cir-
cuitry or not, please consult the “XRT7300 E3/DS3/STS-1 LIU IC” data sheet.
Writing a “1” to Bit 5 of the Line Interface Drive Register (Address = 0x72) will
cause this output pin to toggle “High”. Writing a “0” to this bit-field will cause
this output pin to toggle “Low”.
NOTE: If the designer is not using the XRT7300 E3/DS3/STS-1 LIU IC, then
this output pin can be used for other purposes.
PIN DESCRIPTION (CONTINUED)
PIN NO.
SYMBOL
TYPE
DESCRIPTION
相关PDF资料 |
PDF描述 |
|---|---|
| XRT73L02MIV-F | IC LIU E3/DS3/STS-1 2CH 100TQFP |
| XRT73L03BIV-F | IC LIU E3/DS3/STS-1 3CH 120LQFP |
| XRT73L04BIV-F | IC LIU E3/DS3/STS-1 4CH 144LQFP |
| XRT73L06IB-F | IC LIU E3/DS3/STS-1 6CH 217BGA |
| XRT73LC00AIV-F | IC LIU STS1/DS3/E3 SGL 44TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT72L71IQ-F | 功能描述:网络控制器与处理器 IC Single CH DS3 UNI (3.3V) RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| XRT72L73IB | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Telecommunication IC |
| XRT72L74IB | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Telecommunication IC |
| XRT7300 | 制造商:EXAR 制造商全称:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT7300ES | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。