参数资料
| 型号： | XRT8001ID-F |
| 厂商： | Exar Corporation |
| 文件页数： | 39/48页 |
| 文件大小： | 0K |
| 描述： | IC WAN T1/E1 DUAL 18SOIC |
| 标准包装： | 20 |
| 类型： | 时钟/频率发生器 |
| PLL： | 是 |
| 主要目的： | 以太网（WAN），T1/E1 |
| 输入： | 时钟 |
| 输出： | 时钟 |
| 电路数： | 1 |
| 比率 - 输入:输出： | 1:2 |
| 差分 - 输入:输出： | 无/无 |
| 频率 - 最大： | 16.384kHz |
| 电源电压： | 3.3 V ~ 5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 18-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 18-SOIC |
| 包装： | 管件 |
| 其它名称： | 1016-1358-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
XRT8001
44
Rev. 1.01
10.1 Reading Figures 25 and 26
Figures 25 and 26 are linear (as opposed to logarithmic)
plots. The Jitter Gain is computed via the following
equation.
Jitter
Gain
(at
Jitter
Frequency
f)
=
(Jitter_Amplitude_CLK)/(Jitter_Amplitude_FIN)
Where:
Jitter_Amplitude_FIN = The Jitter Amplitude ap-
plied to the “FIN” input (at Jitter Frequency f).
Jitter_Amplitude_CLK = The Jitter Amplitude
measured at the “CLK1” or “CLK2” output, when
“Jitter_Amplitude_FIN” is applied to the FIN input
in of the XRT8001.
Hence, the Jitter Gain is not expressed in terms of dB,
but simply a ratio of two numbers.
Wherever the Jitter Gain exceeds “1.0” in value, then,
for those “Jitter Frequencies” the XRT8001 amplifies
Jitter (e.g., the amplitude of the jitter, as it propagates
from the “FIN” input to the “CLK1” or CLK2” output,
increases).
Conversely, wherever the Jitter Gain falls below “1.0”
in value, then for those “Jitter Frequencies” the
XRT8001 attenuates jitter (e.g., the amplitude of the
jitter, as it propagates from the “FIN” input to the “CLK1”
or “CLK2” output, decreases).
Figures 25 and 26 indicate that for Jitter Frequencies,
ranging between 100Hz and 1100Hz, the XRT8001
amplifies Jitter. Further, these figures also indicate
that for Jitter Frequencies greater than 1100Hz, that
the XRT8001 attenuates Jitter.
10.2 Test Conditions for Measurements associated
with Figures 25 and 26
Power Supply voltage either 3.3V or 5.V
Input Clock Frequency = 2.048MHz
Output Clock Frequency = 2.048MHz
Input Jitter Amplitude = 0.25Upp.
Ambient Temperature = 25°C.
11.0 PCB layout guidelines for the XRT8001
Use a multi-layer circuit board with separate plane
layers for “+5V” (or 3.3V) and “Ground” .
BypasstheAnalogVDDpintogroundwitha6.9mF
“ceramic” capacitor.
Use large “vias” located close to the IC package to
ensure that Digital VDD (e.g., pins 7, 12 and 15)
and Digital Ground (e.g., pins 4, 5 and 14) have a
low inductance path to the +5V (+3.3V) and Ground
Planes, respectively.
BypasstheDigitalVDDpins(pin10)togroundwith
a 0.1mF ceramic capacitors that are located as
close as possible to the IC package.
12.0 Comparing the XRT8001 with the earlier pin-
compatible XRT8000
The XRT8001 is pin-to-pin compatible with the
XRT8000. However, there are some functional differ-
ences between these two products. These differences
are summarized below.
1) The XRT8001 can be configured to generate frequen-
cies up to 2.048MHz, 4.096MHz, 8.192MHz or
16.384MHz.
The Maximum Frequency that the XRT8000 can gen-
erate is either 2.048MHz or 1.544MHz
2) The XRT8001 can be configured to accept an E1 rate
clock signal and synthesize a T1 rate clock signal. The
XRT8001 can also synthesize an E1 rate clock signal,
when provided with a T1 rate clock signal
The XRT8000 can be configured to accept a T1 rate
clock signal (e.g., 1.544MHz) and can be easily config-
ured to synthesize an E1 rate clock signal (e.g.,
2.048MHz).
However, the XRT8000 cannot be configured to accept
an E1 rate clock signal and synthesize a T1 rate clock
signal.
相关PDF资料 |
PDF描述 |
|---|---|
| XRT8000ID-F | IC WAN CLOCK E1/E1 DUAL 18SOIC |
| D38999/24FH53SA | CONN RCPT 53POS JAM NUT W/SCKT |
| VE-BW0-MW-F2 | CONVERTER MOD DC/DC 5V 100W |
| MS3110F22-55SY | CONN RCPT 55POS WALL MNT W/SCKT |
| VE-BW0-MW-F1 | CONVERTER MOD DC/DC 5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT8001ID-F | 制造商:Exar Corporation 功能描述:WAN Clock IC |
| XRT8001IDTR-F | 功能描述:锁相环 - PLL RoHS:否 制造商:Silicon Labs 类型:PLL Clock Multiplier 电路数量:1 最大输入频率:710 MHz 最小输入频率:0.002 MHz 输出频率范围:0.002 MHz to 808 MHz 电源电压-最大:3.63 V 电源电压-最小:1.71 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:QFN-36 封装:Tray |
| XRT8001IP | 制造商:EXAR 制造商全称:EXAR 功能描述:WAN Clock for T1 and E1 Systems |
| XRT8001IP-F | 功能描述:锁相环 - PLL RoHS:否 制造商:Silicon Labs 类型:PLL Clock Multiplier 电路数量:1 最大输入频率:710 MHz 最小输入频率:0.002 MHz 输出频率范围:0.002 MHz to 808 MHz 电源电压-最大:3.63 V 电源电压-最小:1.71 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:QFN-36 封装:Tray |
| XRT8010 | 制造商:EXAR 制造商全称:EXAR 功能描述:312MHZ CLOCK & CRYSTAL MULTIPLIER WITH LVDS OUTPUTS |
发布紧急采购，3分钟左右您将得到回复。