参数资料
| 型号： | XRT8001ID-F |
| 厂商： | Exar Corporation |
| 文件页数： | 47/48页 |
| 文件大小： | 0K |
| 描述： | IC WAN T1/E1 DUAL 18SOIC |
| 标准包装： | 20 |
| 类型： | 时钟/频率发生器 |
| PLL： | 是 |
| 主要目的： | 以太网（WAN），T1/E1 |
| 输入： | 时钟 |
| 输出： | 时钟 |
| 电路数： | 1 |
| 比率 - 输入:输出： | 1:2 |
| 差分 - 输入:输出： | 无/无 |
| 频率 - 最大： | 16.384kHz |
| 电源电压： | 3.3 V ~ 5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 18-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 18-SOIC |
| 包装： | 管件 |
| 其它名称： | 1016-1358-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页当前第47页第48页
XRT8001
8
Rev. 1.01
Bits 2 Through 5: The Four (4) Bit Address Values
(Labeled A0, A1, A2 and A3)
The next four rising edges of the SCLK signal will clock
in the 4-bit address value for this particular Read (or
Write) operation. The address selects the Command
Register, within the XRT8001, that the user will either
be reading data from, or writing data to. The user must
supply the address bits to the SDI input pin in ascend-
ing order with the LSB (least significant bit) first.
Bits 6 and 7:
The next two bits, A4 and A5, must be set to “0”, as
shown in Figure 19.
Bit 8 - A6
The value of “A6” is a “don’t care”. Once these first
eight bits have been written into the Microprocessor
Serial Interface, the subsequent action depends upon
whether the current operation is a “Read” or “Write”
operation.
Read Operation
Once the last address bit (A3) has been clocked into
the SDI input, the “Read” operation will proceed through
an idle period, lasting three SCLK periods. On the
falling edge of SCLK Cycle #8 (see Figure 19) the serial
data output signal (SDO) becomes active. At this point
the user can begin reading the data contents of the
addressed Command Register (at Address [A3, A2,
A1, A0]) via the SDO output pin. The Microprocessor
Serial Interface will output this 5-bit data word (D0
through D4) in ascending order (with the LSB first), on
the falling edges of the SCLK pin. As a consequence,
the data (on the SDO output pin) will be sufficiently
stable for reading (by the Microprocessor), on the very
next rising edge of the SCLK pin.
1.0 Operating the Microprocessor Serial
Interface
The XRT8001 Serial Interface is a simple four-wire
interface that is compatible with many of the
microcontrollers available in the market. This interface
consists of the following signals:
CSB
-
Chip Select (Active Low)
SCLK
-
Serial Clock
SDI
-
Serial Data Input
SDO
-
Serial Data Output
Using the Microprocessor Serial Interface
The following instructions, for using the Micropro-
cessor Serial Interface, are best understood by
referring to the diagram in Figure 19.
In order to use the Microprocessor Serial Interface
the user must first provide a clock signal to the
SCLK input pin. Afterwards, the user will initiate a
“Read” or “Write” operation by asserting the “active-
low” Chip Select input pin (CSB). It is important to
assert the CSB pin (e.g., toggle it “low”) at least
50ns prior to the very first rising edge of the clock
signal.
Once the CSB input pin has been asserted, the type of
operation and the target register address must now be
specified by the user. The user provides this informa-
tion to the Microprocessor Serial Interface by writing
eight serial bits of data into the SDI input. Note: each
of these bits will be “clocked” into the SDI input on the
rising edge of SCLK. These eight bits are identified and
described below.
Bit 1 - “R/W” (Read/Write) Bit
This bit will be clocked into the SDI input on the first
rising edge of SCLK (after CSB has been asserted).
This bit indicates whether the current operation is a
“Read” or “Write” operation. A “1” in this bit specifies
a “Read” operation; whereas, a “0” in this bit specifies
a “Write” operation.
相关PDF资料 |
PDF描述 |
|---|---|
| XRT8000ID-F | IC WAN CLOCK E1/E1 DUAL 18SOIC |
| D38999/24FH53SA | CONN RCPT 53POS JAM NUT W/SCKT |
| VE-BW0-MW-F2 | CONVERTER MOD DC/DC 5V 100W |
| MS3110F22-55SY | CONN RCPT 55POS WALL MNT W/SCKT |
| VE-BW0-MW-F1 | CONVERTER MOD DC/DC 5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT8001ID-F | 制造商:Exar Corporation 功能描述:WAN Clock IC |
| XRT8001IDTR-F | 功能描述:锁相环 - PLL RoHS:否 制造商:Silicon Labs 类型:PLL Clock Multiplier 电路数量:1 最大输入频率:710 MHz 最小输入频率:0.002 MHz 输出频率范围:0.002 MHz to 808 MHz 电源电压-最大:3.63 V 电源电压-最小:1.71 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:QFN-36 封装:Tray |
| XRT8001IP | 制造商:EXAR 制造商全称:EXAR 功能描述:WAN Clock for T1 and E1 Systems |
| XRT8001IP-F | 功能描述:锁相环 - PLL RoHS:否 制造商:Silicon Labs 类型:PLL Clock Multiplier 电路数量:1 最大输入频率:710 MHz 最小输入频率:0.002 MHz 输出频率范围:0.002 MHz to 808 MHz 电源电压-最大:3.63 V 电源电压-最小:1.71 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:QFN-36 封装:Tray |
| XRT8010 | 制造商:EXAR 制造商全称:EXAR 功能描述:312MHZ CLOCK & CRYSTAL MULTIPLIER WITH LVDS OUTPUTS |
发布紧急采购，3分钟左右您将得到回复。