参数资料
| 型号： | AD5522JSVDZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 28/64页 |
| 文件大小： | 0K |
| 描述： | IC PMU QUAD 16BIT DAC 80-TQFP |
| 产品变化通告： | Improve FI ac crosstalk |
| 设计资源： | Parametric Measurement Unit and Supporting Components for PAD Appls Using AD5522 and AD7685 (CN0104) |
| 标准包装： | 1 |
| 类型： | 每引脚参数测量单元（PPMU） |
| 应用： | 自动测试设备 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 80-TQFP 裸露焊盘 |
| 供应商设备封装： | 80-TQFP（12x12） |
| 包装： | 托盘 |
| 产品目录页面： | 798 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
AD5522
Data Sheet
Rev. E | Page 34 of 64
When configured as DUTGND per channel, this dual function
pin is no longer connected to the input of the guard amplifier.
Instead, it is connected to the low end of the instrumentation
amplifier (SW14a), and the input of the guard amplifier is
connected internally to MEASVHx (SW13a).
DUTGND
MEASURE
VOLTAGE
IN-AMP
MEASVH[0:3]
GUARD[0:3]
GUARDIN[0:3]/
DUTGND[0:3]
DUT
GUARD
AMP
SW14
SW13
SW16
b
a
–
+
×1
AGND
06197-
029
Figure 49. Using the DUTGND per Channel Feature
GUARD AMPLIFIER
A guard amplifier allows the user to bootstrap the shield of
the cable to the voltage applied to the DUT, ensuring minimal
drops across the cable. This is particularly important for
measurements requiring a high degree of accuracy and in leakage
current testing.
If not required, all four guard amplifiers can be disabled via the
serial interface (system control register). Disabling the guard
amplifiers decreases power consumption by 400 μA per channel.
As described in the Device Under Test Ground (DUTGND)
section, GUARDINx/DUTGNDx are dual function pins. Each
pin can function either as a guard amplifier input for one chan-
nel or as a DUTGND input for one channel, depending on the
requirements of the end application (see Figure 49).
A guard alarm event occurs when the guard output moves more
than 100 mV away from the guard input voltage for more than
200 μs. In this case, the event is flagged via the open-drain output
CGALM. Because the guard and clamp alarm functions share
the same alarm output, CGALM, the alarm information (alarm
trigger and alarm channel) is available via the serial interface in
the alarm status register.
Alternatively, the serial interface allows the user to set up the
CGALM output to flag either the clamp status or the guard
status. By default, this open-drain alarm pin is an unlatched
output, but it can be configured as a latched output via the serial
interface (system control register).
COMPENSATION CAPACITORS
Each channel requires an external compensation capacitor
(CCOMP) to ensure stability into the maximum load capacitance
while ensuring that settling time is optimized. In addition, one
CFF pin per channel is provided to further optimize stability and
settling time performance when in force voltage (FV) mode. When
changing from force current (FI) mode to FV mode, the internal
switch connecting the CFF capacitor is automatically closed.
Although the force amplifier is designed to drive load capacitances
up to 10 nF (with CCOMP capacitor = 100 pF), it is possible to
use larger compensation capacitor values to drive larger loads,
at the expense of an increase in settling time. If a wide range of
load capacitances must be driven, an external multiplexer
connected to the CCOMPx pin allows optimization of settling
time vs. stability. The series resistance of a switch placed on
CCOMPx should typically be <50 Ω.
Suitable multiplexers for use are the ADG1404, ADG1408, or
one of the multiplexers in the ADG4xx family, which typically
have on resistances of less than 50 .
Similarly, connecting the CFF node to an external multiplexer
or ADG1209 family of multiplexers meet these requirements.
The series resistance of the multiplexer used should be such that
1/(2π × RON × CDUT) > 100 kHz
The voltage range of the CFFx and CCOMPx pins is the same as
the voltage range expected on the FOHx pin; therefore, choice
of capacitor must take this into account.
Table 12. Suggested Compensation Capacitor Selection
CLOAD
CCOMP Capacitor
CFF Capacitor
≤1 nF
100 pF
220 pF
≤10 nF
100 pF
1 nF
≤100 nF
CLOAD/100
CLOAD/10
相关PDF资料 |
PDF描述 |
|---|---|
| ESC65DRTI | CONN EDGECARD 130PS DIP .100 SLD |
| AMC30DRTS | CONN EDGECARD 60POS .100 DIP SLD |
| AMC30DRES | CONN EDGECARD 60POS .100 EYELET |
| ASC31DRAS | CONN EDGECARD 62POS .100 R/A DIP |
| RGM40DTMT | CONN EDGECARD 80POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5522JSVUZ | 功能描述:IC PMU QUAD 16BIT DAC 80-TQFP RoHS:是 类别:集成电路 (IC) >> 专用 IC 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
| AD5522JSVUZ-RL | 功能描述:Per-Pin Parametric Measurement Unit (PPMU) IC Automatic Test Equipment 80-TQFP-EP (12x12) 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:有效 类型:每引脚参数测量单元（PPMU） 应用:自动测试设备 安装类型:表面贴装 封装/外壳:80-TQFP 裸露焊盘 供应商器件封装:80-TQFP-EP（12x12） 标准包装:1,000 |
| AD5523JCPZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad Parametric Measurement Unit With Integrated 16-Bit Level Setting DACs |
| AD5530 | 制造商:AD 制造商全称:Analog Devices 功能描述:Serial Input, Voltage Output 12-/14-Bit DACs |
| AD5530_07 | 制造商:AD 制造商全称:Analog Devices 功能描述:Serial Input, Voltage Output 12-/14-Bit Digital-to-Analog Converters |
发布紧急采购，3分钟左右您将得到回复。