参数资料
| 型号： | AD7294BCPZRL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 17/49页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT I2C/SRL 1M 56LFCSP |
| 标准包装： | 2,500 |
| 类型： | ADC，DAC |
| 分辨率（位）： | 12 b |
| 采样率（每秒）： | 22.22k |
| 数据接口： | I²C，串行 |
| 电压电源： | 模拟和数字 |
| 电源电压： | 4.4 V ~ 5.5 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 56-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 56-LFCSP-VQ（8x8） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
Data Sheet
AD7294
Rev. H | Page 23 of 48
gain. Therefore, for an input voltage of ±200 mV at the pins, an
output span of ±2.5 V is generated.
The current sensors on the AD7294 are designed to remove
any flicker noise and offset present in the sensed signal. This is
achieved by implementing a chopping technique that is transpa-
the analog inputs to the amplifiers are then swapped, and the
differential voltage is once again converted by the AD7294. The
two conversion results enable the digital removal of any offset
or noise. Switches on the amplifier inputs enable this chopping
technique to be implemented. This process requires 6 μs in total
to return a final result.
Choosing RSENSE
The resistor values used in conjunction with the current sense
amplifiers on the AD7294 are determined by the specific appli-
cation requirements in terms of voltage, current, and power.
Small resistors minimize power dissipation, have low inductance
to prevent any induced voltage spikes, and have good tolerance,
which reduce current variations. The final values chosen are a
compromise between low power dissipation and good accuracy.
Low value resistors have less power dissipated in them, but higher
value resistors may be required to utilize the full input range of
the ADC, thus achieving maximum SNR performance.
When the sense current is known, the voltage range of the
AD7294 current sensor (200 mV) is divided by the maximum
sense current to yield a suitable shunt value. If the power dissi-
pation in the shunt resistor is too large, the shunt resistor can
be reduced, in which case, less of the ADC input range is used.
Using less of the ADC input range results in conversion results,
which are more susceptible to noise and offset errors because
offset errors are fixed and are thus more significant when
smaller input ranges are used.
RSENSE must be able to dissipate the I2R losses. If the power dissi-
pation rating of the resistor is exceeded, its value may drift or
the resistor may be damaged resulting in an open circuit. This
can result in a differential voltage across the terminals of the
AD7294 in excess of the absolute maximum ratings. Additional
protection is afforded to the current sensors on the AD7294 by
the recommended current limiting resistors, RF1 and RF2, as
illustrated in Figure 43. The AD7294 can handle a maximum
continuous current of 30 mA; thus, an RF2 of 1 k provides
adequate protection for the AD7294.
If ISENSE has a large high frequency component, take care to
choose a resistor with low inductance. Low inductance metal
film resistors are best suited for these applications.
Current Sense Filtering
In some applications, it may be desirable to use external
filtering to reduce the input bandwidth of the amplifier (see
Figure 43). The 3 dB differential bandwidth of this filter is
equal to
BWDM = 1/(4πRC)
Note that the maximum series resistance on the RS(+) and
RS() inputs (as shown in Figure 42) is limited to a maximum
of 1 kΩ due to back-to-back ESD protection diodes from RS(+)
and RS() to VPP. Also, note that if RF1 and RF2 are in series
with R1 and R2 (shown in Figure 42), it affects the gain of the
amplifier. Any mismatch between RF1 and RF2 can introduce
offset error.
05747-
098
RF1
RF2
CF
AD7294
VPP
RSENSE
ILOAD
RSx(–)
RSx(+)
10nF
VPP
Figure 43. Current Sense Filtering (RSX Can Be Either RS1 or RS2)
For certain RF applications, the optimum value for RF1 and
RF2 is 1 kΩ whereas CF1 can range from 1 μF to 10 μF. CF2 is a
decoupling capacitor for the VPP supply. Its value is application
dependant, but for initial evaluation, values in the range of 1 nF
to 100 nF are recommended.
Kelvin Sense Resistor Connection
When using a low value sense resistor for high current
measurement, the problem of parasitic series resistance can
arise. The lead resistance can be a substantial fraction of the
rated resistance, making the total resistance a function of lead
length. Avoid this problem by using a Kelvin sense connection.
This type of connection separates the current path through the
resistor and the voltage drop across the resistor. Figure 44 shows
the correct way to connect the sense resistor between the RS(+)
and RS() pins of the AD7294.
SENSE RESISTOR
CURRENT
FLOW FROM
SUPPLY
CURRENT
FLOW TO
LOAD
KELVIN
SENSE
TRACES
AD7294
RSX(+)
RSX(–)
05747-
031
Figure 44. Kelvin Sense Connections (RSX Can Be Either RS1 or RS2)
ANALOG COMPARATOR LOOP
The AD7294 contains two setpoint comparators that are used
for independent analog control. This circuitry enables users
to quickly detect if the sensed voltage across the shunt has
相关PDF资料 |
PDF描述 |
|---|---|
| AD7306AN | IC TXRX RS-232 RS-422 24-DIP |
| AD7339BSZ-REEL | IC ADC/QUAD DAC 5V W/REF 52-MQFP |
| AD7376ARUZ100 | IC POT DIGITAL 128POS 14-TSSOP |
| AD7391SRZ | IC DAC 10BIT SERIAL 3V 8SOIC |
| AD7392AR | IC DAC 12BIT PARALLEL 3V 20-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7294BSUZ | 功能描述:模数转换器 - ADC 12B Monitor & Cntrl System w/ Temp Sensr RoHS:否 制造商:Analog Devices 通道数量: 结构: 转换速率: 分辨率: 输入类型: 信噪比: 接口类型: 工作电源电压: 最大工作温度: 安装风格: 封装 / 箱体: |
| AD7294BSUZRL | 制造商:Analog Devices 功能描述:Temp Sensor Digital Serial (2-Wire, I2C) 64-Pin TQFP 制造商:Analog Devices 功能描述:TEMP SENSOR DGTL SERL (2-WIRE, I2C) 64TQFP - Tape and Reel 制造商:Analog Devices 功能描述:IC ADC 12BIT W/DAC/TEMP 64TQFP 制造商:Analog Devices Inc. 功能描述:Analog to Digital Converters - ADC 12-Bit Multi-Channel ADC DAC wt Temp IC 制造商:Analog Devices 功能描述:CONVERTER - ADC |
| AD7298 | 制造商:AD 制造商全称:Analog Devices 功能描述:8-Channel, 1MSPS, 12-Bit SAR ADC with Temperature Sensor |
| AD7298-1BCPZ | 功能描述:IC ADC 10BIT SPI/SRL 8CH 20LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD7298-1BCPZ-RL | 功能描述:IC ADC 10BIT SPI/SRL 8CH 20LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
发布紧急采购，3分钟左右您将得到回复。