参数资料
| 型号： | AD7294BCPZRL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 41/49页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT I2C/SRL 1M 56LFCSP |
| 标准包装： | 2,500 |
| 类型： | ADC，DAC |
| 分辨率（位）： | 12 b |
| 采样率（每秒）： | 22.22k |
| 数据接口： | I²C，串行 |
| 电压电源： | 模拟和数字 |
| 电源电压： | 4.4 V ~ 5.5 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 56-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 56-LFCSP-VQ（8x8） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页当前第41页第42页第43页第44页第45页第46页第47页第48页第49页
Data Sheet
AD7294
Rev. H | Page 45 of 48
LAYOUT AND CONFIGURATION
POWER SUPPLY BYPASSING AND GROUNDING
For optimum performance, carefully consider the power supply
and ground return layout on any PCB where the AD7294 is
used. The PCB containing the AD7294 should have separate
analog and digital sections, each having its own area of the
board. The AD7294 should be located in the analog section
on any PCB.
Decouple the power supply to the AD7294 to ground with
10 F and 0.1 F capacitors. Place the capacitors as physically
close as possible to the device, with the 0.1 F capacitor ideally
right up against the device. It is important that the 0.1 F
capacitor have low effective series resistance (ESR) and low
effective series inductance (ESL); common ceramic types of
capacitors are suitable. The 0.1 F capacitor provides a low
impedance path to ground for high frequencies caused by
transient currents due to internal logic switching. The 10 F
capacitors are the tantalum bead type.
The power supply line should have as large a trace as possible to
provide a low impedance path and reduce glitch effects on the
supply line. Shield clocks and other components with fast
switching digital signals from other parts of the board by a
digital ground. Avoid crossover of digital and analog signals,
if possible. When traces cross on opposite sides of the board,
ensure that they run at right angles to each other to reduce
feedthrough effects on the board. The best board layout
technique is the microstrip technique where the component
side of the board is dedicated to the ground plane only and the
signal traces are placed on the solder side; however, this is not
always possible with a 2-layer board.
Layout Considerations for External Temperature Sensors
Power amplifier boards can be electrically noisy environments,
and care must be taken to protect the analog inputs from noise,
particularly when measuring the very small voltages from a
remote diode sensor.
Take the following precautions:
Place the remote sensing diode as close as possible to
the AD7294. If the worst noise sources are avoided, this
distance can be 4 inches to 8 inches.
Route the D+ and D tracks close together, in parallel,
with grounded guard tracks on each side. Provide a ground
plane under the tracks, if possible.
Use wide tracks to minimize inductance and reduce noise
pickup. A 10 mil track minimum width and spacing is
recommended, as shown in Figure 61.
AGND
D1+
D1–
AGND
0.25mm
05747-
049
Figure 61. Arrangement of Signal Tracks
Try to minimize the number of copper/solder joints
because they can cause thermocouple effects. Where
copper/solder joints are used, make sure that they are
in both the Dx+ and Dx path and are at the same
temperature.
Place a 10 pF capacitor between the base and emitter of the
discrete diode, as close as possible to the diode.
If the distance to the remote sensor is more than 20 cm, the
use of twisted-pair cable is recommended.
Because the measurement technique uses switched current
sources, excessive cable and/or filter capacitance can affect the
measurement. When using long cables, the filter capacitor can
be reduced or removed.
相关PDF资料 |
PDF描述 |
|---|---|
| AD7306AN | IC TXRX RS-232 RS-422 24-DIP |
| AD7339BSZ-REEL | IC ADC/QUAD DAC 5V W/REF 52-MQFP |
| AD7376ARUZ100 | IC POT DIGITAL 128POS 14-TSSOP |
| AD7391SRZ | IC DAC 10BIT SERIAL 3V 8SOIC |
| AD7392AR | IC DAC 12BIT PARALLEL 3V 20-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7294BSUZ | 功能描述:模数转换器 - ADC 12B Monitor & Cntrl System w/ Temp Sensr RoHS:否 制造商:Analog Devices 通道数量: 结构: 转换速率: 分辨率: 输入类型: 信噪比: 接口类型: 工作电源电压: 最大工作温度: 安装风格: 封装 / 箱体: |
| AD7294BSUZRL | 制造商:Analog Devices 功能描述:Temp Sensor Digital Serial (2-Wire, I2C) 64-Pin TQFP 制造商:Analog Devices 功能描述:TEMP SENSOR DGTL SERL (2-WIRE, I2C) 64TQFP - Tape and Reel 制造商:Analog Devices 功能描述:IC ADC 12BIT W/DAC/TEMP 64TQFP 制造商:Analog Devices Inc. 功能描述:Analog to Digital Converters - ADC 12-Bit Multi-Channel ADC DAC wt Temp IC 制造商:Analog Devices 功能描述:CONVERTER - ADC |
| AD7298 | 制造商:AD 制造商全称:Analog Devices 功能描述:8-Channel, 1MSPS, 12-Bit SAR ADC with Temperature Sensor |
| AD7298-1BCPZ | 功能描述:IC ADC 10BIT SPI/SRL 8CH 20LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD7298-1BCPZ-RL | 功能描述:IC ADC 10BIT SPI/SRL 8CH 20LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
发布紧急采购，3分钟左右您将得到回复。