- 您现在的位置：买卖IC网 > PDF目录17103 > AD9785-DPG2-EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD9785 PDF资料下载
参数资料
| 型号： | AD9785-DPG2-EBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 35/64页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD9785 |
| 标准包装： | 1 |
| 系列： | TxDAC® |
| DAC 的数量： | 2 |
| 位数： | 12 |
| 采样率（每秒）： | 800M |
| 数据接口： | 串行 |
| 设置时间： | 22ms |
| DAC 型： | 电流 |
| 工作温度： | -40°C ~ 85°C |
| 已供物品： | 板，缆线，CD |
| 已用 IC / 零件： | AD9785 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
AD9785/AD9787/AD9788
Rev. A | Page 40 of 64
QUADRATURE MODULATOR
The quadrature modulator is used to mix the carrier signal
generated by the NCO with the upsampled I and Q data
provided by the user at the 16-bit parallel input port of the
device. Figure 58 shows a detailed block diagram of the
quadrature modulator.
The NCO provides a quadrature carrier signal with a frequency
determined by the 32-bit frequency tuning word (FTW) set in
Register 0x0A, Bits [31:0]. The NCO operates at the rate equal
to the upsampled I data and Q data. The generated carrier
signal is mixed via multipliers with the I data and Q data. The
quadrature products are then summed.
Note that the sine output of the NCO contains a mux that
allows negating of the data. The mux is controlled with a
spectral inversion bit that the user stores in an I/O register
(Register 0x01, Bit 10). The default condition is to select
negated sine data.
NUMERICALLY CONTROLLED OSCILLATOR
The NCO generates a complex carrier signal to translate the
input signal to a new center frequency. A complex carrier signal
is a pair of sinusoidal waveforms of the same frequency, offset
90° from each other. The frequency of the complex carrier
signal is set via the Frequency Tuning Word [31:0] value in
Register 0x0A. The frequency of the complex carrier signal is
calculated as follows:
If {0 ≤ FTW ≤ 231}, use fCENTER = (FTW) (fDACCLK)/232
If {231 < FTW < 232 1}, use fCENTER = fDACCLK × (1 (FTW/232))
A 16-bit phase offset may be added to the output of the phase
accumulator via the serial port. This static phase adjustment
results in an output signal that is offset by a constant angle
relative to the nominal signal. This allows the user to phase
align the NCO output with some external signal, if necessary.
This can be especially useful when NCOs of multiple AD9785/
AD9787/AD9788 devices are programmed for synchronization.
The phase offset allows for the adjustment of the output timing
between the devices. The static phase adjustment is sourced
from the NCO Phase Offset Word [15:0] value located in
Register 0x0B.
By default, when an SPI write is completed for the frequency
tuning word, phase control, DAC gain scaling, or DAC offset
registers (Register 0x0A through Register 0x0D), the operation
of the AD9785/AD9787/AD9788 is immediately updated to
reflect these changes. However, in many applications it may be
more useful to update these registers without changing the
device operation until all these functions can be updated at
once. With the automatic I/O transfer enable bit set low in the
COMM register (Register 0x00, Bit 1), the value of all these
functions is stored in a buffer after the initial SPI write. To
update all these functions simultaneously, Bit 2 of the COMM
register should be set. This bit is self-resetting and thus does not
require another reset in a later SPI write.
INVERSE SINC FILTER
The inverse sinc filter is implemented as a nine-tap FIR filter. It
is designed to provide greater than ±0.05 dB pass-band ripple
up to a frequency of 0.4 × fDACCLK. To provide the necessary
peaking at the upper end of the pass band, the inverse sinc filter
has an intrinsic insertion loss of 3.4 dB. The tap coefficients are
given in Table 31.
INTERPOLATION
NCO
1
0
–1
COSINE
SINE
I
DATA
Q
DATA
FTW [31:0]
SPECTRAL
INVERSION
OUT_I
OUT_Q
+
–
NCO PHASE OFFSET
WORD [15:0]
07
09
8-
10
7
Figure 58. Quadrature Modulator Block Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| EEM36DTMD-S189 | CONN EDGECARD 72POS R/A .156 SLD |
| EEM36DTMH-S189 | CONN EDGECARD 72POS R/A .156 SLD |
| 0210390421 | CABLE FLAT FLEX 1.18" 1MM 26POS |
| EVAL-AD5791SDZ | BOARD EVAL FOR AD5791 |
| VE-J2R-EZ | CONVERTER MOD DC/DC 7.5V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9785-EBZ | 制造商:Analog Devices 功能描述:Evaluation Board For AD9785 制造商:Analog Devices 功能描述:DUAL 12B, 1GSPS D-A CONVERTER - Bulk 制造商:Analog Devices 功能描述:Digital to Analog Eval. Board |
| AD9786 | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Bit, 200 MSPS/500 MSPS TxDAC+ with 2】/4】/8】 Interpolation and Signal Processing |
| AD9786BSV | 制造商:Analog Devices 功能描述:DAC 1-CH Interpolation Filter 16-bit 80-Pin TQFP EP 制造商:Analog Devices 功能描述:IC 16BIT DAC SMD 9786 TQFP80 |
| AD9786BSVRL | 制造商:Analog Devices 功能描述:DAC 1-CH Interpolation Filter 16-bit 80-Pin TQFP EP T/R |
| AD9786BSVZ | 功能描述:IC DAC 16BIT INTERPOL/SP 80TQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:TxDAC+® 标准包装:1 系列:- 设置时间:4.5µs 位数:12 数据接口:串行，SPI? 转换器数目:1 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOICN 包装:剪切带 (CT) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:* 其它名称:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
发布紧急采购，3分钟左右您将得到回复。