- 您现在的位置：买卖IC网 > PDF目录17103 > AD9785-DPG2-EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD9785 PDF资料下载
参数资料
| 型号： | AD9785-DPG2-EBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 46/64页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD9785 |
| 标准包装： | 1 |
| 系列： | TxDAC® |
| DAC 的数量： | 2 |
| 位数： | 12 |
| 采样率（每秒）： | 800M |
| 数据接口： | 串行 |
| 设置时间： | 22ms |
| DAC 型： | 电流 |
| 工作温度： | -40°C ~ 85°C |
| 已供物品： | 板，缆线，CD |
| 已用 IC / 零件： | AD9785 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页当前第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
AD9785/AD9787/AD9788
Rev. A | Page 50 of 64
ANALOG OUTPUTS
Full-scale current on the I DAC and Q DAC can be set from
8.66 mA to 31.66 mA. Initially, the 1.2 V band gap reference is
used to set up a current in an external resistor connected to
I120 (Pin 75). A simplified block diagram of the reference
circuitry is shown in Figure 69.
I DAC
DAC FULL-SCALE
REFERENCE
CURRENT
SCALING
I DAC GAIN
Q DAC GAIN
Q DAC
AD9788
VREF
10k
5k
1.2V BAND GAP
REFERENCE
0.1F
I120
070
98
-03
0
Figure 69. Full-Scale Current Generation Circuitry
The recommended value for the external resistor is 10 kΩ,
which sets up an IREFERENCE in the resistor of 120 μA, which in
turn provides a DAC output full-scale current of 20 mA. Because
the gain error is a linear function of this resistor, a high precision
resistor improves gain matching to the internal matching
specification of the devices. Internal current mirrors provide
a current-gain scaling, where DAC gain is a 10-bit word in the
SPI port register (Register 0x05 and Register 0x07). The default
value for the DAC gain registers gives an IFS of approximately
20 mA, where IFS for either I DAC or Q DAC is equal to
32
1024
6
12
27
V
2
1
DAC gain
R
.
35
0
1000
DAC GAIN CODE
I FS
(m
A
)
30
25
20
15
10
5
200
400
600
800
07
09
8-
03
1
Figure 70. DAC Full-Scale Current vs. DAC Gain Code
DIGITAL AMPLITUDE SCALING
Gain scaling of the analog DAC output can be achieved by
changing the values in Register 0x05 and Register 0x07.
However, if this is done, the output common-mode voltage at
the analog output also decreases proportionally. This poses a
problem when the AD9785/AD9787/AD9788 are dc-coupled to
a quadrature modulator. Typical quadrature modulators have
tight restrictions on input common-mode variation.
The AD9785/AD9787/AD9788 use a digital gain scaling block
to get around this problem. Because the gain scaling is done in
the digital processing of the AD9785/AD9787/AD9788, there is
no effect on the output full-scale current. This digital gain
scaling is done in such a way that the midscale value of the
signal is unaffected; the swing of the signal around midscale is
the value that is adjusted with the register settings. Digital gain
scaling is done using the amplitude scale factor (ASF) register
(Register 0x0C).
Auxiliary DAC Operation
Two auxiliary DACs are provided on the AD9785/AD9787/
AD9788. The full-scale output current on these DACs is derived
from the 1.2 V band gap reference and external resistor. The
gain scale from the reference amplifier current, IREFERENCE, to the
auxiliary DAC reference current is 16.67 with the auxiliary DAC
gain set to full scale (10-bit values, Register 0x06, Bits [9:0] and
Register 0x08, Bits [9:0]). This gives a full-scale current of approx-
imately 2 mA for Auxiliary DAC 1 and Auxiliary DAC 2.
The auxiliary DAC outputs are not differential. Only one side of
the auxiliary DAC (P or N) is active at one time. The inactive side
goes into a high impedance state (100 kΩ). In addition, the P or N
output can act as a current source or a current sink. Control of
the P and N sides for both auxiliary DACs is via Register 0x06 and
Register 0x08, Bits [15:14]. When sourcing current, the output
compliance voltage is 0 V to 1.6 V. When sinking current, the
output compliance voltage is 0.8 V to 1.6 V.
相关PDF资料 |
PDF描述 |
|---|---|
| EEM36DTMD-S189 | CONN EDGECARD 72POS R/A .156 SLD |
| EEM36DTMH-S189 | CONN EDGECARD 72POS R/A .156 SLD |
| 0210390421 | CABLE FLAT FLEX 1.18" 1MM 26POS |
| EVAL-AD5791SDZ | BOARD EVAL FOR AD5791 |
| VE-J2R-EZ | CONVERTER MOD DC/DC 7.5V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9785-EBZ | 制造商:Analog Devices 功能描述:Evaluation Board For AD9785 制造商:Analog Devices 功能描述:DUAL 12B, 1GSPS D-A CONVERTER - Bulk 制造商:Analog Devices 功能描述:Digital to Analog Eval. Board |
| AD9786 | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Bit, 200 MSPS/500 MSPS TxDAC+ with 2】/4】/8】 Interpolation and Signal Processing |
| AD9786BSV | 制造商:Analog Devices 功能描述:DAC 1-CH Interpolation Filter 16-bit 80-Pin TQFP EP 制造商:Analog Devices 功能描述:IC 16BIT DAC SMD 9786 TQFP80 |
| AD9786BSVRL | 制造商:Analog Devices 功能描述:DAC 1-CH Interpolation Filter 16-bit 80-Pin TQFP EP T/R |
| AD9786BSVZ | 功能描述:IC DAC 16BIT INTERPOL/SP 80TQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:TxDAC+® 标准包装:1 系列:- 设置时间:4.5µs 位数:12 数据接口:串行，SPI? 转换器数目:1 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOICN 包装:剪切带 (CT) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:* 其它名称:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
发布紧急采购，3分钟左右您将得到回复。