- 您现在的位置：买卖IC网 > Datasheet目录307 > ADE5566ASTZF62-RL (Analog Devices Inc)IC ENERGY METERING 1PHASE 64LQFP Datasheet资料下载
参数资料
| 型号： | ADE5566ASTZF62-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 54/156页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING 1PHASE 64LQFP |
| 产品变化通告： | Product Discontinuance 27/Oct/2011 |
| 标准包装： | 1,500 |
| 输入阻抗： | 770 千欧 |
| 测量误差： | 0.1% |
| 电压 - 高输入/输出： | 2V |
| 电压 - 低输入/输出： | 0.8V |
| 电源电压： | 2.4 V ~ 3.7 V |
| 测量仪表类型： | 单相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页当前第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页
ADE5166/ADE5169/ADE5566/ADE5569
–89.70
–89.75
–89.80
Data Sheet
the analog input signal, V2, and the output of LPF1. The phase
lag response of LPF1 results in a time delay of approximately
2 ms (at 60 Hz) between the zero crossing on the analog inputs
of the voltage channel and ZX detection.
–89.85
×1, ×2, ×4,
×8, ×16
REFERENCE
–89.90
–89.95
–90.00
–90.05
V2
V P
V N
{GAIN[7:5]}
PGA2
ADC 2
HPF
LPF1
f –3dB = 63.7Hz
ZERO
CROSSING
ZX
40
45
50
55
60
65
70
FREQUENCY (Hz)
MODE1[6]
Figure 54. Combined Phase Response of the Digital Integrator and
Phase Compensator (40 Hz to 70 Hz)
Note that the integrator has a ?20 dB/dec attenuation and an
approximately ?90° phase shift. When combined with a di/dt
1.0
0.73
43.24° @ 60Hz
ZX
sensor, the resulting magnitude and phase response should be
a flat gain over the frequency band of interest. The di/dt sensor
has a 20 dB/dec gain associated with it. It also generates significant
high frequency noise. Therefore, a more effective antialiasing
filter is needed to avoid noise due to aliasing (see the Antialiasing
Filter section).
When the digital integrator is switched off, the ADE5169/ADE5569
can be used directly with a conventional current sensor, such as a
current transformer (CT), or with a low resistance current shunt.
POWER QUALITY MEASUREMENTS
Zero-Crossing Detection
Each ADE5166/ADE5169/ADE5566/ADE5569 has a zero-
crossing detection circuit on the voltage channel. This external
zero-crossing signal can be output on P0.5 and P1.2 (see Table 39).
It is also used in calibration mode.
The zero crossing is generated by default from the output of LPF1.
This filter has a low cutoff frequency and is intended for 50 Hz
and 60 Hz systems. If needed, this filter can be disabled to allow
a higher frequency signal to be detected or to limit the group delay
of the detection. If the voltage input fundamental frequency is
below 60 Hz, and a time delay in ZX detection is acceptable, it
is recommended that LPF1 be enabled. Enabling LPF1 limits the
variability in the ZX detection by eliminating the high frequency
components. Figure 55 shows how the zero-crossing signal is
generated.
The zero-crossing signal, ZX, is generated from the output of
LPF1 (bypassed or not). LPF1 has a single pole at 63.7 Hz (at
V2 LPF1
Figure 55. Zero-Crossing Detection on the Voltage Channel
The zero-crossing detection also drives the ZX flag in the Inter-
rupt Status 3 SFR (MIRQSTH, Address 0xDE). If the ZX bit (Bit 0)
in the Interrupt Enable 3 SFR (MIRQENH, Address 0xDB) is set,
the 8052 core has a pending ADE interrupt. The ADE interrupt
stays active until the ZX status bit is cleared (see the Energy
Measurement Interrupts section).
Zero-Crossing Timeout
The zero-crossing detection also has an associated timeout
register, ZXTOUT. This unsigned, 12-bit register is decremented
(1 LSB) every 160/MCLK sec. The register is reset to its user-
programmed, full-scale value every time a zero crossing is detected
on the voltage channel. The default power-on value in this register
is 0xFFF. If the internal register decrements to 0 before a zero
crossing is detected in the Interrupt Status 3 SFR (MIRQSTH,
Address 0xDE) and the ZXTO bit (Bit 1) in the Interrupt Enable 3
SFR (MIRQENH, Address 0xDB) is set, the 8052 core has a
pending ADE interrupt.
The ADE interrupt stays active until the ZXTO status bit is
cleared (see the Energy Measurement Interrupts section). The
ZXTOUT register (Address 0x11) can be written to or read by
the user (see the Energy Measurement Registers section). The
resolution of the register is 160/MCLK sec per LSB. Thus, the
maximum delay for an interrupt is 0.16 sec (1/MCLK × 2 12 ) when
MCLK = 4.096 MHz.
MCLK = 4.096 MHz). As a result, there is a phase lag between
Rev. D | Page 54 of 156
相关PDF资料 |
PDF描述 |
|---|---|
| ADE7156ASTZF16 | IC ENERGY METER 64-LQFP |
| ADE7156ASTZF8-RL | IC ENERGY METER 64-LQFP |
| ADE7518ASTZF8-RL | IC ENERGY METER MCU 8K 64LQFP |
| ADE7569ASTZF16 | IC ENERGY METER MCU 16K 64LQFP |
| ADE7752BARWZ-RL | IC ENERGY METERING 3PHASE 24SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE5569 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
| ADE5569ASTZF62 | 功能描述:IC METER/8052/RTC/LCD DRV 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE5569ASTZF62 | 制造商:Analog Devices 功能描述:Energy Management IC |
| ADE5569ASTZF62-RL | 功能描述:IC METER/8052/RTC/LCD DRV 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE-6 | 制造商:MINI 制造商全称:Mini-Circuits 功能描述:Surface Mount Frequency Mixer |
发布紧急采购，3分钟左右您将得到回复。