- 您现在的位置：买卖IC网 > PDF目录20400 > DC1663A (Linear Technology)DEMO BOARD LTM4628 PDF资料下载
参数资料
| 型号： | DC1663A |
| 厂商： | Linear Technology |
| 文件页数： | 12/36页 |
| 文件大小： | 0K |
| 描述： | DEMO BOARD LTM4628 |
| 软件下载： | LTM4628 Spice Model |
| 设计资源： | LTM4628 Gerber Files DC1663A Design Files |
| 标准包装： | 1 |
| 系列： | µModule® |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 2，非隔离 |
| 输出电压： | 1.2V，1.5V |
| 电流 - 输出： | 8A，8A |
| 输入电压： | 4.5 ~ 26.5 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 400kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | LTM4628 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTM4628
APPLICATIONS INFORMATION
V OUT
? D? ( )
I CIN(RMS) =
I OUT(MAX)
InputCapacitors
The LTM4628 module should be connected to a low ac-
impedance DC source. For the regulator input three 22μF,
or four 10μF input ceramic capacitors are used for RMS
ripple current. A 47μF to 100μF surface mount aluminum
electrolytic bulk capacitor can be used for more input bulk
capacitance. This bulk input capacitor is only needed if
the input source impedance is compromised by long in-
ductive leads, traces or not enough source capacitance.
If low impedance power planes are used, then this bulk
capacitor is not needed.
For a buck converter, the switching duty-cycle can be
estimated as:
D =
V IN
Without considering the inductor current ripple, for each
output, the RMS current of the input capacitor can be
estimated as:
1 ? D
η %
In the above equation, η % is the estimated efficiency of the
power module. The bulk capacitor can be a switcher-rated
aluminum electrolytic capacitor or a Polymer capacitor.
Output Capacitors
The LTM4628 is designed for low output voltage ripple
noise and good transient response. The bulk output
capacitors defined as C OUT are chosen with low enough
effective series resistance (ESR) to meet the output volt-
age ripple and transient requirements. C OUT can be a low
ESR tantalum capacitor, the low ESR polymer capacitor
or ceramic capacitor. The typical output capacitance range
for each output is from 200μF to 470μF. Additional output
filtering may be required by the system designer, if further
reduction of output ripples or dynamic transient spikes
is required. Table 4 shows a matrix of different output
voltages and output capacitors to minimize the voltage
droop and overshoot during a 4A/μs transient. The table
optimizes total equivalent ESR and total bulk capacitance
to optimize the transient performance. Stability criteria
are considered in the Table 4 matrix, and LTpowerCAD?
is available for stability analysis. Multiphase operation will
reduce effective output ripple as a function of the num-
ber of phases. Application Note 77 discusses this noise
reduction versus output ripple current cancellation, but
the output capacitance should be considered carefully as
a function of stability and transient response. LTpowerCAD
can calculate the output ripple reduction as the number of
implemented phases increases by N times. A small value
10? to 50? resistor can be placed in series from V OUT
to the V OUTS pin to allow for a bode plot analyzer to inject
a signal into the control loop and validate the regulator
stability. The same resistor could be placed in series from
V OUT to DIFFP and a bode plot analyzer could inject a signal
into the control loop and validate the regulator stability.
Burst Mode Operation
The LTM4628 is capable of Burst Mode operation on
each regulator in which the power MOSFETs operate
intermittently based on load demand, thus saving quiescent
current. For applications where maximizing the efficiency
at very light loads is a high priority, Burst Mode operation
should be applied. Burst Mode operation is enabled with
the MODE_PLLIN pin floating. During this operation, the
peak current of the inductor is set to approximately one
third of the maximum peak current value in normal opera-
tion even though the voltage at the COMP pin indicates
a lower value. The voltage at the COMP pin drops when
the inductor’s average current is greater than the load
requirement. As the COMP voltage drops below 0.5V, the
Burst comparator trips, causing the internal sleep line to
go high and turn off both power MOSFETs.
In sleep mode, the internal circuitry is partially turned off,
reducing the quiescent current to about 450μA for each
output. The load current is now being supplied from the
output capacitors. When the output voltage drops, caus-
ing COMP to rise above 0.5V, the internal sleep line goes
low, and the LTM4628 resumes normal operation. The
next oscillator cycle will turn on the top power MOSFET
and the switching cycle repeats. Either regulator can be
configured for Burst Mode operation.
4628fe
12
For more information www.linear.com/LTM4628
相关PDF资料 |
PDF描述 |
|---|---|
| IFSC1008ABER220M01 | INDUCTOR POWER 22UH 0.5A SMD |
| GSC10DRYI | CONN EDGECARD 20POS DIP .100 SLD |
| AT24C08B-TH-T | IC EEPROM 8KBIT 1MHZ 8TSSOP |
| T95Z226K016LSAL | CAP TANT 22UF 16V 10% 2910 |
| 346-080-540-202 | CARDEDGE 80POS DUAL .125 GREEN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1666A | 功能描述:BOARD DEMO LED DRIVER LT3791 RoHS:否 类别:编程器，开发系统 >> 评估板 - LED 驱动器 系列:- 标准包装:1 系列:PowerWise® 电流 - 输出 / 通道:20mA 输出及类型:1，非隔离 输出电压:17V 特点:可调光 输入电压:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相关产品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
| DC1667 | 制造商:INTRONICS 制造商全称:INTRONICS 功能描述:15 Watt Triple Output DC-DC Converters |
| DC1668 | 制造商:INTRONICS 制造商全称:INTRONICS 功能描述:15 Watt Triple Output DC-DC Converters |
| DC1669 | 制造商:INTRONICS 制造商全称:INTRONICS 功能描述:15 Watt Triple Output DC-DC Converters |
| DC1669A | 功能描述:BOARD EVAL LTM4627 RoHS:否 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:LTM®, uModule® 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
发布紧急采购，3分钟左右您将得到回复。