- 您现在的位置：买卖IC网 > PDF目录20400 > DC1663A (Linear Technology)DEMO BOARD LTM4628 PDF资料下载
参数资料
| 型号： | DC1663A |
| 厂商： | Linear Technology |
| 文件页数： | 17/36页 |
| 文件大小： | 0K |
| 描述： | DEMO BOARD LTM4628 |
| 软件下载： | LTM4628 Spice Model |
| 设计资源： | LTM4628 Gerber Files DC1663A Design Files |
| 标准包装： | 1 |
| 系列： | µModule® |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 2，非隔离 |
| 输出电压： | 1.2V，1.5V |
| 电流 - 输出： | 8A，8A |
| 输入电压： | 4.5 ~ 26.5 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 400kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | LTM4628 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTM4628
APPLICATIONS INFORMATION
? C SS ?
t SOFT-START = ? ? ? 0.6V
? 60.4k = R TB
R TA =
+ FB ? TRACK
whentheRUNpinisbelow1.2V.Thetotalsoft-starttime
can be calculated as:
? 1.3μA ?
Regardless of the mode selected by the MODE_PLLIN pin,
the regulator channels will always start in pulse-skipping
mode up to TRACK = 0.5V. Between TRACK = 0.5V and
0.54V, it will operate in forced continuous mode and revert
to the selected mode once TRACK > 0.54V. In order to
track with another channel once in steady state operation,
the LTM4628 is forced into continuous mode operation
as soon as V FB is below 0.54V regardless of the setting
on the MODE_PLLIN pin.
Ratiometric tracking can be achieved by a few simple cal-
culations and the slew rate value applied to the master’s
TRACK pin. As mentioned above, the TRACK pin has a
control range from 0 to 0.6V. The master’s TRACK pin
slew rate is directly equal to the master’s output slew rate
in Volts/Time. The equation:
MR
SR
where MR is the master’s output slew rate and SR is the
slave’s output slew rate in Volts/Time. When coincident
tracking is desired, then MR and SR are equal, thus R TB
is equal the 60.4k. R TA is derived from equation:
0.6V
V FB V V
60.4k R FB R TB
where V FB is the feedback voltage reference of the regula-
tor, and V TRACK is 0.6V. Since R TB is equal to the 60.4k
top feedback resistor of the slave regulator in equal slew
rate or coincident tracking, then R TA is equal to R FB with
V FB = V TRACK . Therefore R TB = 60.4k, and R TA = 60.4k in
Figure 6.
In ratiometric tracking, a different slew rate maybe desired
for the slave regulator. R TB can be solved for when SR
is slower than MR. Make sure that the slave supply slew
rate is chosen to be fast enough so that the slave output
voltage will reach it final value before the master output.
For example, MR = 1.5V/1ms, and SR = 1.2V/1ms. Then
R TB = 76.8k. Solve for R TA to equal to 49.9k.
Each of the TRACK pins will have the 1.3μA current source
on when a resistive divider is used to implement tracking
on that specific channel. This will impose an offset on the
TRACK pin input. Smaller values resistors with the same
ratios as the resistor values calculated from the above
equation can be used. For example, where the 60.4k is
used then a 6.04k can be used to reduce the TRACK pin
offset to a negligible value.
Power Good
The PGOOD pins are open drain pins that can be used to
monitor valid output voltage regulation. This pin monitors
a ±7.5% window around the regulation point. A resistor
can be pulled up to a particular supply voltage no greater
than 6V maximum for monitoring.
Stability Compensation
The module has already been internally compensated for
all output voltages. Table 4 is provided for most application
requirements. LTpowerCAD is available for other control
loop optimization.
Run Enable
The RUN pins have an enable threshold of 1.4V maximum,
typically 1.25V with 150mV of hysteresis. They control
the turn-on of each of the channels. These pins can be
pulled up to V IN for 5V operation, or a 5V Zener diode can
be placed on the pins and a 10k to 100k resistor can be
placed up to higher than 5V input for enabling the chan-
nels. The RUN pins can also be used for output voltage
sequencing. In parallel operation the RUN pins can be
tie together and controlled from a single control. See the
Typical Application circuits in Figure 28. The RUN pin can
also be left floating. The RUN pin has a 1μA pull-up cur-
rent source that increases by an additional 4.5μA during
ramp-up once above the on/off threshold.
4628fe
For more information www.linear.com/LTM4628
17
相关PDF资料 |
PDF描述 |
|---|---|
| IFSC1008ABER220M01 | INDUCTOR POWER 22UH 0.5A SMD |
| GSC10DRYI | CONN EDGECARD 20POS DIP .100 SLD |
| AT24C08B-TH-T | IC EEPROM 8KBIT 1MHZ 8TSSOP |
| T95Z226K016LSAL | CAP TANT 22UF 16V 10% 2910 |
| 346-080-540-202 | CARDEDGE 80POS DUAL .125 GREEN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1666A | 功能描述:BOARD DEMO LED DRIVER LT3791 RoHS:否 类别:编程器，开发系统 >> 评估板 - LED 驱动器 系列:- 标准包装:1 系列:PowerWise® 电流 - 输出 / 通道:20mA 输出及类型:1，非隔离 输出电压:17V 特点:可调光 输入电压:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相关产品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
| DC1667 | 制造商:INTRONICS 制造商全称:INTRONICS 功能描述:15 Watt Triple Output DC-DC Converters |
| DC1668 | 制造商:INTRONICS 制造商全称:INTRONICS 功能描述:15 Watt Triple Output DC-DC Converters |
| DC1669 | 制造商:INTRONICS 制造商全称:INTRONICS 功能描述:15 Watt Triple Output DC-DC Converters |
| DC1669A | 功能描述:BOARD EVAL LTM4627 RoHS:否 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:LTM®, uModule® 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
发布紧急采购，3分钟左右您将得到回复。